To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind your tail lights. You will have to remove the tail lights to access this harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.6 out of 5 stars (17 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.My mistake the first one I ordered but thanks to the folks at etrailer I was able to purchase the rignt on and exchange the wrong one at the same time and get my hitch installed just in time, thank you etrailer!
Everything worked great including the v ideos
This is a good wiring harness and worked well right off the bat after installation. It does requires some tricky work with fish wires that is quite difficult. Five stars for function, three stars for a rather difficult installation.
Excellent fit. Working with no hoist on concrete floor took me 1 1/2 hr. working alone. Fit just as advertised. ——————-————————————————————————————— Electrical wiring a bit more involved, a hoist would be good. The challenging part is running the 12 volt wire to the battery with the removal of the underbody panels required. Still excellent product. Both videos helpful.
Takes time but it was good.
wires were not long enough. Plugs were too close together to reach out behind the light fixture i had to splice all the wires to reach and make it work.
Their customer service was great. Handled everything quickly and efficiently and kept me notified the whole time.
It went in very well, I did have to extend one wire that was too short the way I routed it but it worked perfectly. Everything else fit like a glove. Very happy with my purchase
Every item I ordered came a day earlier than expected, quality was excellent, instruction video on installing the hitch as well as the wireing absolutely helped. Everything went really smooth but I had a lift that helped
Have not had timeto install. Other priority items need to be taken care of first.
Grateful you had my Items in stock. Very impressed with shipping the order right away and getting delivered on the Exact date. Very professional Definitely order from you again.
Worked as advertised but the wiring was a little short.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.