Replacement New-Style Linc Analog Remote - 5 Function

See what our Experts say about this Lippert Accessories and Parts

• Can the Lippert Replacement Analog Remote Control Multiple Lights
  I contacted Lippert Components on your behalf and the Replacement New-Style Linc Analog Remote # LC292614 light control button on the remote will control a single light function at a time but not different lights throughout the unit as you asked. What light function is controlled depends on how the multi-function board is wired. Some customers have that board wired to control the awning lights or other lights on their unit but it is essentially like having a single light switch.
  view full answer...
• Finding Momentary Push Button for Programming LINC Remote
  The momentary push button is actually not on the remote part # LC292614 that you referenced. It's on the receiver of the LINC system. I reread the instructions a few times till I caught that too so I understand the confusion! Normally the receiver is located above where your generator is stored.
  view full answer...
  
• Replacement Lippert Remote for 5-Function Controller with Fuses
  I spoke with Lippert and they said because remote # LC292614 is analog you would first need the original Linc remote in order to program the fuses on the board. But assuming they are already programmed you could use remote # LC292614. Since you just lost your remote that likely means your board is already programmed.
  view full answer...
• Could Replacement New-Style Linc Analog Remote Work on Keystone Montana
  Since I can't verify that your Keystone Montana has the LCI Linc setup which the remote part # LC292614 is designed to work with I can't say for certain. But if this looks just like the remote you had then yes this would be the correct replacement. If you had something that looks different send me any info you can on what you have. A picture of the mounted control panel or any part numbers you can find would be really helpful.
  view full answer...
• Troubleshooting Linc Analog Remote Timing Out While In Use
  I reached out to Lippert and there is no way to alter the timeout interval on the remote. However, this should not be going blank in such a short period of time. Lippert recommends resyncing the # LC292614 to see if that fixes the issue. This can be done with the following steps: 1. Press and hold the momentary push button on the receiver. 2. Press “Light” (A) button on the transmitter until relay on receiver “clicks”. 3. Release momentary push button. 4. The transmitter is synced to...
  view full answer...
• How Does Replacement New-Style Linc Analog Remote Pair to Transmitter
  I attached a picture that I took from the install instructions for the Replacement New-Style Linc Analog Remote # LC292614 which you referenced. The syncing process is outlined there.
  view full answer...
  
• What Does Lippert Linc Setup Do for RVs
  The Lippert Linc system that the remote part # LC292614 is designed to work with is an option that OEM RV manufacturers will install on their campers to give you one remote to control most of the power options of the trailer. For example the slide outs, the awnings, the stabilizer jacks, the landing gear jacks. Basically the three top buttons control things that slide out like awnings and slide outs. You'll press select to highlight which you wish to control and then press in and out to...
  view full answer...
• Remote Control For 2022 Jayco Eagle
  It sounds like you are looking for the replacement analog remote # LC292614. The remote for the slide outs, awnings, lights, and jacks. This is not specific to Jayco models necessarily. It will work with any camper equipped with a Lippert brand transmitter. The Lippert systems are extremely common on campers like your Jayco Eagle.
  view full answer...
• Replacement Linc Remote for a Forest River Sonoma RV
  The Replacement New-Style Linc Analog Remote part # LC292614 is the correct replacement for your 2017 Forest River Sonoma 240RKS. The etrailer logo in the lower right hand corner is just a sticker we place on our products for advertising purposes but it will not be on the actual remote you receive.
  view full answer...
• Finding Receiver for Pairing Replacement Lippert LINC Remote
  The receiver location for the Lippert LINC system that you need to access to pair the Replacement Remote # LC292614 can vary between different trailer/RV models but typically it's somewhere near where the generator is stored. If you can't find the receiver there then your best bet will be to try and contact the trailer/RV manufacturer and they should be able to tell you its whereabouts.
  view full answer...
  
• Troubleshooting Lippert Linc Remote that Stopped Working After Battery Replacement
  You probably lost the pairing of your remote # LC292614 to the receiver. To pair it again hold down the momentary switch of your receiver, press and hold the button the remote with the light bulb on it till you hear a click in the receiver. Once you release the button it will be synced.
  view full answer...
• Recommended Replacement Analog Remote for a 2015 Forest River Salem Hemisphere
  It sounds like you're looking for the Replacement New-Style Linc Analog Remote # LC292614. This remote has the 5 functions you're looking for to control your slide out, awning, lights, leveling/stabilizing jacks, and will work with your Lippert system.
  view full answer...
• Could Replacement New-Style Linc Analog Remote # LC292614 Work on 2011 Keystone Montana
  If your current remote looks like the Replacement New-Style Linc Analog Remote # LC292614 then yes this would be the correct replacement for it. If it doesn't we do not have a solution.
  view full answer...
• Where is Momentary Switch To Program Replacement New Style Linc Analog Remote
  The momentary button you are looking for on the receiver that you need to find to program the Replacement New-Style Linc Analog Remote # LC292614 is typically located above where your generator is stored.
  view full answer...
• Could Replacement New-Style Linc Remote Work for 2014 Forest River Wildcat Maxx
  If you have the Linc system in your 2014 Forest River Wildcat Maxx travel trailer the part # LC292614 would work for you. But if you have a different setup you'd need to look at something else.
  view full answer...
• Signal Used by New-Style Linc Analog Remote
  I reached out to the manufacturer, Lippert, who told me the Replacement New-Style Linc Analog Remote - 5 Function # LC292614 works off an RF signal.
  view full answer...
• Where is the Lippert LINC Receiver Located On My Coach
  Usually you will find the LINC remote control receiver in the same compartment as your generator; on this receiver there will be a push button that you're looking for. This is the button mentioned in the instructions as the momentary switch that will be used during the programming process of the Replacement New-Style Linc Analog Remote - 5 Function # LC292614.
  view full answer...
  
• Will Replacement New Style Linc Analog Remote Work on 2013 Denali Travel Trailer
  Yes the Replacement New-Style Linc Analog Remote # LC292614 that you referenced can control your slide out, stabilizer jacks front and back, and awning and porch light and was designed for 2013 year RVs with the Linc system.
  view full answer...
• Does Remote Need to be Changed When Fuse is Blown to Activate Functions on 5th Wheel Trailer
  If you are having a fuse blow when you use a remote, like part # LC292614, for your 2018 Forest River Wildwood Heritage Ultra Lite then that is an indication that you need to check the wiring for the remote. If something were not activating then the remote could be the culprit but it wouldn't be able to cause a fuse to blow. Check the wiring from the receiver for the remote and make sure everything has a solid connection and there aren't any places with exposed wiring or a bad ground....
  view full answer...
• Troubleshooting Replacement New-Style Linc Analog Remote LC292614 Not Syncing
  It looks like you have the Lippert remote control part # LC292614. I have attached instructions on how to link the remote to the receiver. Our contact at Lippert said if the remote does not pair with the receiver then the remote may have blown a fuse, in that situation it would need to be replaced. They also recommended to make sure the batteries in the remote are present and in working order before you complete these steps: 1) Press and hold the momentary push button on the receiver. 2)...
  view full answer...
  
• Programming Instructions Recommendation for New Style LCI Linc Remote
  Is your remote the part # LC292614? I attached a picture that I took from the install instructions for the Replacement New-Style Linc Analog Remote # LC292614 which you referenced. The syncing process is outlined there.
  view full answer...
  
• Lippert Analog Remote Will Not Control Awning
  It sounds like the Lippert remote control part # LC292614 is not fully syncing to the receiver. I have attached instructions on how to sync the remote. 1) Press and hold the momentary push button on the receiver. 2) Press “Light” (A) button on the transmitter until relay on receiver “clicks”. 3) Release momentary push button. 4) The transmitter is synced to the receiver.
  view full answer...
  
• Troubleshooting Outside Light Function Not Working with the Lippert New-Style Linc Analog Remote
  I reached out to my contact at Lippert who said that the light function that your New-Style Linc Analog Remote # LC292614 activate will have a relay or fuse. Since everything else is working the relay/fuse is likely bad and needs to be replaced. You will need to find where this is located in regards to the control panel for your specific application.
  view full answer...
• Troubleshooting LCI Remote Not Working With All Functions on 2018 Salem Hemisphere 5th Wheel
  If some functions magically stopped working with your LCI system and the New-Style Linc Analog Remote # LC292614 then I recommend power-cycling your system to see if the system self-corrects. You'll do this by disconnecting the power connections, waiting a few minutes, and then reconnecting them to see if that fixes anything. If it does - great! If it doesn't - please reach out and let me know and I can help you troubleshoot further.
  view full answer...

Do you have a question about this Accessories and Part?