Replacement Bearings, Races, Grease Seals and Retainers For a 3,500LB Axle On a 2015 Surveyor 264RKS
Updated 09/13/2022 | Published 09/11/2022
Products Featured in This Question
Question:
I have a 2015 Forrest River Surveyor model 264RKS, Two 3500lb axles, brakes on both. I want to repack the bearings. I need four grease seals for the repack and I want a spare bearing kit to keep while traveling. What part numbers do I need? Thanks.
asked by: David E
Expert Reply:
For your 2015 Forest River Surveyor 264RKS with tow 3,500lb axles you will need the Grease Seals # RG06-050. These are sold as a 2-pack for one axle so you will need 2 sets for your tandem axles. The Seal Puller # PTW1219 will help you to remove the old seals without risking damage to the bearings or races on your hub/drums. We do have replacement Tang Washers # 5-101 and Nut Retainers # 6-190 available if yours cannot be reused. Both of these will work with your Super Lube axle spindle but you will need to verify which retainer you may need.
For a spare set of parts the Bearing Kit # BK2-100 will contain both inner and outer races along with inner and outer bearings, a grease seal, tang washer and cotter pin. You will want to keep the 7-Piece Installation Set # PTW83020 with this kit so that you will be able to correctly install the new races without damaging them.
Product Page this Question was Asked From
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Search Results: trailer bearing kit
- Search Results: bk2 100 bearing kit
- Search Results: led trailer light kit
- Q&A: Can Marine Wheel Bearing Grease Be Used In a Utility Trailer
- Shop: TowSmart 4-Way Flat to 4-Way Flat Trailer Wiring Harness Extension Kit - 18" Long
- Q&A: What Diameter Thread Are The DX82CR Spindle Retainer Nuts?
- Q&A: Can Spindle Nut Be Reused When Installing Bearing Kit for #84 Spindle
- Q&A: Is there a Replacement O-Ring that Sits at the Back of the Spindle Before the Backing Plate?
- Q&A: How to Find the Spindle Number on a Trailer Axle
- Q&A: Which Grease Cap And Spindle Nut Do I Need For Bearing Kit # BK2-100
- Q&A: How To Find Correct Replacement Bearings and Hub for Outback Trailer with AL-KO Axles
- Shop: Replacement Nut Retainer for 6-191 Jam Nut
- Shop: Replacement Trailer Axle Spindle Retainer Kit for Dexter Axles Manufactered After June 2002
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5-1/2- Pre-Greased
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Video: Measuring To Choose The Right Trailer Axle
- Search Results: trailer jack
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Brake Controller
on Trailer Bearings Races Seals Caps
