Replacement Bearing Kit and Grease Cap for Dexter Trailer Hub 8-248
Updated 09/29/2025 | Published 05/11/2025
Products Featured in This Question
Question:
I am looking for the bearing kit for a Dexter 8-248 Hub with the EZ-Lube Spindle. It has the Jam Nut and Nut Retainer Clip. I would also want new EZ-Lube covers. Can I get help with these part numbers?
asked by: Michael Y
0
Expert Reply:
Hey Michael, the hub you have uses the bearing kit part # BK2-100 for replacement bearings/seal/races since it is a 3,500 lb axle hub. For a replacement EZ lube style grease cap you'd then want the part # RG04-040.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Search Results: dexter axle grease cap
- Search Results: axle cotter pin
- Search Results: grease fitting
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Shop: EZ Lube Grease Caps with 1.99" OD - Fits 7" and 10" x 1-1/4" Dexter Hubs - Qty 2
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Q&A: What Size Grease Seal And Dust Cap is Needed on a 3,500 Lbs. Axle With L44649 Outer Bearing
- Shop: Dexter Grease Caps with 1.99" OD - Fits 7" and 10" Hubs - Zinc-Plated Steel - Qty 2
- Video: All You Need to Know About the Grease Cap, 1.99" OD EZ Lube Drive in with Plug
- Shop: Replacement EZ Lube Drive-In Grease Cap - 1.986" OD - Qty 1
- Shop: Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery - Top Load
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Article: Most Popular Wheel Bearings
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Trailer Wiring Diagrams
- Q&A: Bearing Kit for 2017 Jayco Jay Flight 17BH
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: How to Tell the Weight Rating of a Trailer Axle
- Q&A: Bearing Kit for Lippert 4,400 lb Trailer Axle
- Q&A: Replacement Bearing And Seals For UFP Hub H-1062-2
- Q&A: Replacement Hub/Rotor and Bearings for Tie Down Engineering TDE46245
- Q&A: What is the Best Grease for Trailer Bearings
- Article: How to Bleed Your Trailer Surge Brakes
Jameson C.
9/29/2025
Hey Michael, did the bearing kit and EZ-Lube covers work out for your Dexter hub? I'm asking because your experience could help others with similar setups.