Can Spindle Nut Be Reused When Installing Bearing Kit for #84 Spindle
Published 09/20/2022
Products Featured in This Question
Question:
Hello! My spindle has a flat for the nut retainer using the wire cage . This spindle is not drilled for a cotter key. Should I just re-use the retainer nut?
asked by: Larry M
Expert Reply:
Yes, if the retainer nut is in good shape you can use all of the other components of the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle # BK2-100 and not worry about the tang washer and cotter pin.
If the spindle nut isn't in good shape then you can replace those parts as well with the Spindle Nut Kit for EZ Lube Axles # RG05-100.
Attached is an installation video of the bearing kit and a review video of the spindle nut kit for you to check out.
Product Page this Question was Asked From
Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer bearing kit
- Search Results: bk2 100 bearing kit
- Search Results: led trailer light kit
- Q&A: Can Marine Wheel Bearing Grease Be Used In a Utility Trailer
- Q&A: How to Find the Spindle Number on a Trailer Axle
- Q&A: Replacement Hub for Utility Trailer with Dexter 8-256 Hub
- Q&A: What Size Grease Seal And Dust Cap is Needed on a 3,500 Lbs. Axle With L44649 Outer Bearing
- Q&A: Is there a Replacement O-Ring that Sits at the Back of the Spindle Before the Backing Plate?
- Q&A: How To Find Correct Replacement Bearings and Hub for Outback Trailer with AL-KO Axles
- Q&A: Replacement Bearings, Races, Grease Seals and Retainers For a 3,500LB Axle On a 2015 Surveyor 264RKS
- Shop: Replacement Nut Retainer for 6-191 Jam Nut
- Shop: Replacement Trailer Spindle Jam Nut - 1" Diameter - Plain
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Grease Cap, 1.99" OD EZ Lube Drive in with Plug - Qty 2
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5-1/2- Pre-Greased
- Shop: Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Search Results: trailer tires and wheels
- Video: Measuring To Choose The Right Trailer Axle
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: trailer wiring
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer jack
- Video: How to Choose a Trailer Brake Controller
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Bearings Races Seals Caps
