Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hey Skip, welcome back! The Vitrifrigo RV Refrigerator w/ Freezer item #VT56FR is going to need a 12v power supply. You can not plug it into a standard 110v outlet. You'll need to use the PowerMax AC to DC Converter item #PM54VR, which works with…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hey Nang, the mounting holes on the back of the MORryde TV bracket part #MR85ZR can accommodate bolt sizes that are up to M8 in diameter. M8 is 8mm (about 0.315 inches) across its threads, while 1/4-20 is 0.25 inches. Typically TV hardware is M4, M5,…
Hey John, welcome back! I do have a way better functional solution for you. It's the Brandmotion Tailgate Delete Backup Camera with Wiring Harness item #BM67JR. This camera attaches to your license plate bracket. The other end will connect to the…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
Hey Randy, congrats on the new motorhome. Your 2026 Entegra Odyssey 24B was built on a 2025 Ford E-450 Chassis so the Safe-T-Plus Steering Stabilizer with Mounting Hardware Kit item #ST98MR will indeed fit. This kit comes with the stabilizer,…
The MORryde Wall RV TV Mount #MR23ZR has dimensions of 5.25" W x 5.83" T for the plate that attaches to the wall. The MORryde Wall RV TV Mount #MR65ZR has dimensions of 10" W x 5.87" T for the plate that attaches to the wall.…
Hey Bill, yes the Furrion Vision S+ #FR64AD would be a direct replacement for your current Vision S system. None of it is backwards compatible with the standard Vision S system though.
Hey, Henery! We sure do! We currently carry the Cummins Onan QG 2500i RV generator with inverter, part #CM25ZR. This generator does run on propane and has an electronic ignition. If you need additional specs or details just let me know, I’d be happy…
Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hey Skip, welcome back! The Vitrifrigo RV Refrigerator w/ Freezer item #VT56FR is going to need a 12v power supply. You can not plug it into a standard 110v outlet. You'll need to use the PowerMax AC to DC Converter item #PM54VR, which works with…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hey Nang, the mounting holes on the back of the MORryde TV bracket part #MR85ZR can accommodate bolt sizes that are up to M8 in diameter. M8 is 8mm (about 0.315 inches) across its threads, while 1/4-20 is 0.25 inches. Typically TV hardware is M4, M5,…
Hey John, welcome back! I do have a way better functional solution for you. It's the Brandmotion Tailgate Delete Backup Camera with Wiring Harness item #BM67JR. This camera attaches to your license plate bracket. The other end will connect to the…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
Hey Randy, congrats on the new motorhome. Your 2026 Entegra Odyssey 24B was built on a 2025 Ford E-450 Chassis so the Safe-T-Plus Steering Stabilizer with Mounting Hardware Kit item #ST98MR will indeed fit. This kit comes with the stabilizer,…
The MORryde Wall RV TV Mount #MR23ZR has dimensions of 5.25" W x 5.83" T for the plate that attaches to the wall. The MORryde Wall RV TV Mount #MR65ZR has dimensions of 10" W x 5.87" T for the plate that attaches to the wall.…
Hey Bill, yes the Furrion Vision S+ #FR64AD would be a direct replacement for your current Vision S system. None of it is backwards compatible with the standard Vision S system though.
Hey, Henery! We sure do! We currently carry the Cummins Onan QG 2500i RV generator with inverter, part #CM25ZR. This generator does run on propane and has an electronic ignition. If you need additional specs or details just let me know, I’d be happy…
Dial in your rig with an RV TV mount that can swing, swivel, or pull down for a comfortable angle and lock for travel. Match your TV's weight to the mount's rating, like 25 lb or 50 lb, and factor in the mount's own weight; check VESA patterns from 75 x 75 to 200 x 200 or use an adapter for 300 x 300 or 400 x 400. Install into a stud or backing, and be ready for small tweaks like longer bolts or plug clearance.
Often, yes. Verify your mount's VESA pattern first; many accept 75 x 75, 100 x 100, 200 x 100, and 200 x 200. If your TV is 300 x 300 or 400 x 400, a VESA adapter plate that attaches via the 200 x 200 pattern can bridge the gap. Confirm your TV's exact pattern before buying an adapter.
Yes, mount into a stud or vertical support; you can't just screw to an RV wall. RV walls can be near paper-thin and supports may be few and far apart, so locate solid backing. If the designated spot doesn't have a label listing a max weight/size, reach out to your RV manufacturer for guidance.
Check bolt length; supplied bolts may be too short for some displays. Confirm clearance around the TV's power plug—trimming part of a bracket has been needed, using a jig saw with a metal blade. Making a template for the base bolt layout can simplify positioning. If a slide-in bracket feels tight, align carefully before lifting. Adding foam can help reduce rattling in travel.
Yes, if your TV's weight is within the mount's listed capacity, like 50 lb. Match your TV's VESA pattern; mounts commonly fit 75 x 75, 100 x 100, 200 x 100, and 200 x 200. If your TV is 300 x 300 or 400 x 400, use a VESA adapter plate that ties into the 200 x 200 pattern. If a spot lists a max weight/size, stay within it.
RV TV Mount Parts or Accessories
Filters
