Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hey Skip, welcome back! The Vitrifrigo RV Refrigerator w/ Freezer item #VT56FR is going to need a 12v power supply. You can not plug it into a standard 110v outlet. You'll need to use the PowerMax AC to DC Converter item #PM54VR, which works with…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hey Nang, the mounting holes on the back of the MORryde TV bracket part #MR85ZR can accommodate bolt sizes that are up to M8 in diameter. M8 is 8mm (about 0.315 inches) across its threads, while 1/4-20 is 0.25 inches. Typically TV hardware is M4, M5,…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
Hey John, welcome back! I do have a way better functional solution for you. It's the Brandmotion Tailgate Delete Backup Camera with Wiring Harness item #BM67JR. This camera attaches to your license plate bracket. The other end will connect to the…
Hey Jonathan, congrats on the new truck. The 7" drop should be enough, but it is hard to say for sure without knowing what trailer you will be pulling. The 7" drop will get your ball height at 17" or 18" (we measure from the upper…
The Lippert Patio Upgrade Kit for Toy Hauler Garage Doors #LC27FR is a complete kit. It has all the hardware and struts that you need to convert your garage door into a patio. It may seem confusing because there were optional side rails that you…
The MORryde Wall RV TV Mount #MR23ZR has dimensions of 5.25" W x 5.83" T for the plate that attaches to the wall. The MORryde Wall RV TV Mount #MR65ZR has dimensions of 10" W x 5.87" T for the plate that attaches to the wall.…
Hey Bill, yes the Furrion Vision S+ #FR64AD would be a direct replacement for your current Vision S system. None of it is backwards compatible with the standard Vision S system though.
WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!
Eric
Cedar Springs, MI
RV TV Mount with 180 Degrees Swivel
Slide it out from a storage bay and swivel it 180 degrees to aim your screen where you want. Made for RV storage areas, these mounts can go on a left or right wall; the handle location just ends up on the opposite side when flipped. Plan for door clearance—on most RVs you'll need extra mounting height or spacers, and solid support, since the mount is heavy duty.
Yes, mounting on either side is workable. The handle or locks may end up on a different edge when flipped, so check that you can reach and operate them. Test the slide and swivel path to be sure it extends and locks as intended on your chosen side.
Confirm your TV's VESA pattern matches the mount and that your TV weight stays within the mount's capacity. Measure the compartment width and opening to ensure the TV can slide out and the door can close. If space is tight, consider a smaller screen. Reinforce the wall or backing to handle the mount's weight.
Yes, the wide swivel works well for sliding out and pivoting to watch outside. Plan cable routing to both the cable/TV and satellite connections and label them for quick changes later. Expect access to the TV ports to be tight after install, so get cable lengths and paths set beforehand.
It can, but you may need added mounting height or spacers to clear the door. Measure the door opening and TV width before drilling. If the base length isn't adjustable, simple spacer blocks can make up the difference. These mounts can be heavy, so reinforce the mounting surface to support the weight.
Filters
