Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hey Skip, welcome back! The Vitrifrigo RV Refrigerator w/ Freezer item #VT56FR is going to need a 12v power supply. You can not plug it into a standard 110v outlet. You'll need to use the PowerMax AC to DC Converter item #PM54VR, which works with…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hey Nang, the mounting holes on the back of the MORryde TV bracket part #MR85ZR can accommodate bolt sizes that are up to M8 in diameter. M8 is 8mm (about 0.315 inches) across its threads, while 1/4-20 is 0.25 inches. Typically TV hardware is M4, M5,…
Hey John, welcome back! I do have a way better functional solution for you. It's the Brandmotion Tailgate Delete Backup Camera with Wiring Harness item #BM67JR. This camera attaches to your license plate bracket. The other end will connect to the…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
The MORryde Wall RV TV Mount #MR23ZR has dimensions of 5.25" W x 5.83" T for the plate that attaches to the wall. The MORryde Wall RV TV Mount #MR65ZR has dimensions of 10" W x 5.87" T for the plate that attaches to the wall.…
Hey Bill, yes the Furrion Vision S+ #FR64AD would be a direct replacement for your current Vision S system. None of it is backwards compatible with the standard Vision S system though.
Hey Randy, congrats on the new motorhome. Your 2026 Entegra Odyssey 24B was built on a 2025 Ford E-450 Chassis so the Safe-T-Plus Steering Stabilizer with Mounting Hardware Kit item #ST98MR will indeed fit. This kit comes with the stabilizer,…
Hey, Henery! We sure do! We currently carry the Cummins Onan QG 2500i RV generator with inverter, part #CM25ZR. This generator does run on propane and has an electronic ignition. If you need additional specs or details just let me know, I’d be happy…
Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hey Skip, welcome back! The Vitrifrigo RV Refrigerator w/ Freezer item #VT56FR is going to need a 12v power supply. You can not plug it into a standard 110v outlet. You'll need to use the PowerMax AC to DC Converter item #PM54VR, which works with…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hey Nang, the mounting holes on the back of the MORryde TV bracket part #MR85ZR can accommodate bolt sizes that are up to M8 in diameter. M8 is 8mm (about 0.315 inches) across its threads, while 1/4-20 is 0.25 inches. Typically TV hardware is M4, M5,…
Hey John, welcome back! I do have a way better functional solution for you. It's the Brandmotion Tailgate Delete Backup Camera with Wiring Harness item #BM67JR. This camera attaches to your license plate bracket. The other end will connect to the…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
The MORryde Wall RV TV Mount #MR23ZR has dimensions of 5.25" W x 5.83" T for the plate that attaches to the wall. The MORryde Wall RV TV Mount #MR65ZR has dimensions of 10" W x 5.87" T for the plate that attaches to the wall.…
Hey Bill, yes the Furrion Vision S+ #FR64AD would be a direct replacement for your current Vision S system. None of it is backwards compatible with the standard Vision S system though.
Hey Randy, congrats on the new motorhome. Your 2026 Entegra Odyssey 24B was built on a 2025 Ford E-450 Chassis so the Safe-T-Plus Steering Stabilizer with Mounting Hardware Kit item #ST98MR will indeed fit. This kit comes with the stabilizer,…
Hey, Henery! We sure do! We currently carry the Cummins Onan QG 2500i RV generator with inverter, part #CM25ZR. This generator does run on propane and has an electronic ignition. If you need additional specs or details just let me know, I’d be happy…
WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!
Set up your screen with MORryde RV TV mounts that feel solid and easy to use. Options cover common VESA patterns like 75 x 75, 100 x 100, 200 x 100, and 200 x 200, with adapters available for 300 x 300 or 400 x 400. For a trouble-free install, match the mount and TV weight to the rating and secure into a stud or backing plate in your RV.
Make a template of the base bolt layout to simplify positioning. The slide-in bracket can be a tight fit—support the TV and align carefully. Some setups may need a small metal trim for plug clearance; a jigsaw with a metal blade works. Swivel range can be limited on certain mounts. For travel, lock the TV upright and add foam to reduce rattling.
Yes, as long as the TV is within the mount's weight rating. MORryde options include 25 lb and 50 lb capacities, and users have run 40"-65" screens when the weight fit the rating. Confirm your TV's actual weight and include mount weight when assessing your RV wall. If your TV is 46 lbs, pair it with a 50 lb-rated mount.
Mount it into a stud or solid vertical support. RV walls can be thin, so add a backed plate like plywood to spread the load if needed. Don't just screw into paneling, and be careful with fastener length so you don't run screws through an outside wall. Use the included hardware that matches your wall structure.
Yes, if your TV's VESA matches what the MORryde mount supports. Check for patterns like 75 x 75, 100 x 100, 200 x 100, or 200 x 200. If your TV is 300 x 300 or 400 x 400, use a VESA adapter plate. Verify plug clearance on the back of the TV—some TVs need a small bracket cutout for the power plug.
RV TV Mount Parts or Accessories
Filters
