Replacing Shorelander Fenders with Marker Lights

Question

Question:

Replacing a Shorelander Fender that had the marker lites. I don't see any holes for the bolts on the step which the old fender bolted too. Would drilling them hurt the integrity of the fender. This is the 3rd fender to have to be replace after a blow out and it is getting expensive with the dealer sk 0121.03 models

asked by: Big G

0

Expert Reply:

The brackets we recommend for the plastic fenders are the # CE26098G-2. Don't worry, drilling a hole into the fender for the bracket to mount to your trailer will not hurt the structural integrity of the Fulton Fenders # F008584-2 you were looking at.

If you are also in need of an inexpensive marker light, I recommend the Optronics Prewired Fender Ligth # BA44FNR for the right side and the # BA44FNL for the left side.

expert reply by: Jackie C

0

Answer 1

Thanks for the pictures Jaime. The Peterson item #M152A is what you'll need to replace the marker light in your Shorelandr boat trailer's fender. This is an incandescent light that measures 2-1/2" wide x 1-1/4" wide. It is sold…

view full answer...

Answer 2

For other options we have #MCL95AB for amber lights and #MCL95RB for red. They're still surface mounted lights but the base is included and may work for you. They're also a single wire design so they ground through the mounting hardware. If…

view full answer...

Answer 3

Whether it be lights or lenses, to order replacements for your Shorelander boat trailer, you can either try and locate a part number on the light housing (not the lens) or take a quick measurement of the light and order by size. I have included a…

view full answer...

Answer 4

I do have an option for you but we do not carry Shoreland'r branded boat trailer parts. However, I was able to do some research on your boat trailer and came back with the Fulton Single Axle Trailer Fenders part #F008574-2. These are not an OEM…

view full answer...

Answer 5

The Fulton trailer fenders part #F008584-2 would be a really great option for both sides of your Shoreland'r trailer that would closely match what came on it originally. To see if we have a cap or lid for your surge brake actuator will require…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacing Shorelander Fenders with Marker Lights

Products Featured in This Question

Continue Researching