Looking For Replacement For Fender Clearance Light P2 05 S90

Question

Question:

I have a Fender clearance light...P2 05 S90 and am looking for a replacement. Is MCL180ARB good replacement?

asked by: Mark E

0

Expert Reply:

Hello Mark; we do offer a variety of fender lights, so we very well may have a replacement for you. We do not have a direct replacement for the P2 05 S90 light that you mentioned though. After searching for a few pictures of these lights, what I saw looks similar to the LED Trailer Fender Clearance Light # MCL180ARB that you mentioned. This light measures 8-1/2" long x 1-11/16" tall x 13/16" deep and it has mounting holes 1" apart. Please measure one of your lights and verify that this is a match. If you need something different, we do offer several others like the fender-mount lights # MCL67ARB, # MCL12ARLB, # BA44FNR and # BA44FNL. If you can let me know the dimensions of your light, or even send a picture or two I am happy to look into it and see what we can offer you.

expert reply by: Jesse M

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

Great question, William! The Karrier ST225/75R15 #KE63KV is a KR35 while the Karrier ST225/75R15 #AM10303 is a KR03 according to Kenda. There is a slight variation in the tread pattern and from what Kenda says about them it looks like the KR03 is…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 11

Karrier and Loadstar are two different brand names used by Kenda. There's no difference in quality or function between the two brand names. For a ST175/80-13 Radial trailer tire in load range D, I'd recommend part #AM10210 if you're…

view full answer...

Answer 12

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Looking For Replacement For Fender Clearance Light P2 05 S90

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching