Product Experts Available Now!
Call 1-800-940-8924
Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
(222 reviews)
Price: $37.11
In Stock
We'll connect you with nearby partnered installers who know this exact setup.
Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
Part Number: E4139
In Stock
$37.11
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
We'll connect you with nearby partnered installers who know this exact setup.
- All Info
- Reviews (222)
- Q & A (0)
- Videos (1)
- Photos
Redline Trailer Suspension Parts - E4139
Highlights
- 4-1/4" Tall Design: Adds lift for better ground clearance and level towing.
- Handles up to 7,000 lbs: Strong enough for heavy trailers and long-haul use.
- Works Front, Center, or Rear: One hanger style covers multiple suspension points.
- Fits 1-3/4" Wide Double-Eye Springs: Matches the common spring width for easy fit.
- 9/16" Bolt Hole: Accepts standard wet or dry bolts for secure suspension mounting.
- 3/16" Thick Steel: Durable weld-on construction resists flex and elongation over time.
Features to know about
More Ground Clearance Without Replacing the Axle: 4-1/4" Tall Hanger Adds Height
When you need a little extra room under the trailer but can’t use an over/under kit, a taller hanger is the simple fix. This 4-1/4" tall hanger gives your suspension more drop, helping lift the trailer frame for better clearance over curbs, driveways, or rough gravel roads. It’s a practical way to restore ride height on a sagging setup or add lift for better leveling with a high-riding tow vehicle.
Built to Handle the Load: Rated for Axles Up to 7,000 lbs
Strength matters when you’re hanging thousands of pounds of trailer weight on a few inches of steel. This Redline hanger is rated for axles up to 7,000 lbs and made from 3/16" thick steel. It provides a solid, reliable connection point for your suspension so every mile stays steady and controlled.
One Part, Many Positions: Fits Front, Center, or Rear Mounts
You don’t need three different hangers for one job. This single piece can be used in front, center, or rear positions to suspend your double-eye leaf spring or equalizer. That makes it handy for single, tandem, or triple-axle setups and simplifies replacement when you’re rebuilding or upgrading the suspension.
Sized Right for Common Hardware: 9/16" Bolt Hole and 1-3/4" Wide Springs
Getting the right fit keeps the suspension moving smoothly. The hanger works with 9/16" diameter spring eyes and bolts (sold separately) and fits 1-3/4" wide double-eye springs. With an outside width of 2-5/16", it lines up cleanly for a solid weld-on installation and keeps your springs and equalizers swinging freely without binding.
Durable and Easy to Work With: 3/16" Thick Steel for Confident Welding
A hanger has to take years of flex and vibration, so this one is built from 3/16" thick steel that’s ready to weld directly to the trailer frame. That solid construction resists elongation and wear around the bolt hole, keeping your suspension geometry true and your ride consistent mile after mile.
Specs
Dimensions
- Height: 4-1/4"
- Outside width: 2-5/16"
- Inside width: 1-15/16"
- Thickness of metal: 3/16"
Compatibility
- Spring type: Double-eye leaf springs
- Spring width: 1-3/4"
- Bolt hole diameter: 9/16"
- Axle application: Up to 7,000 lbs
- Configuration: Front, center, or rear hanger
- Axle setups: Single axle, tandem axle, triple axle
E4139 Front, Center or Rear Hanger for Double Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
Video of Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Checking Out the Front/Center/Rear Hanger for Double-Eye Springs
Today, we're going to be taking a look at the front, center, or rear hanger, for double-eye springs. This hanger can be used as a front hanger on single axle applications, and it can be used as a front, center, or rear hanger, on tandem or triple axle applications. It's going to fit 1 3/4" wide double-eye springs with 9/16" diameter eyes. It does work with a 9/16" diameter bolt, hardware sold separately. The unit's made from a sturdy steel construction. It measures around 3/16" thick.
It is a weld-on application, so this will weld directly to the trailer frame. The height measurement for a hanger is taken from the center of the mount hold to the top of the hanger. The height for this particular one is going to give us a measurement of about 4 1/4". The overall length, looking at about 3". External width is about 2 5/6" to 2 3/8".
Internal width, it's going to measure about 1 7/8 to 1 15/16", and then the overall height of the unit, that's going to measure about 4 7/8" tall. Then the holes on the unit, again, have that diameter of 9/16". That's going to do it for today's look at the front, center, or rear hanger, for double-eye springs.
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Product did not meet expectations
- Wrong item was ordered
- Alternate product found
Ratings & Reviews
4.8
222 reviews
by:
Nathan
04/25/2020
These were purchased to assist with raising a dual-axle travel trailer. They arrived well packaged, and looked to be well made.They took readily to welding, so there was no issue with inferior material. The attached images show them being welded side-by-side to the frame rail extensions, then the entire assembly attached to the main frame.
by:
Keith
10/09/2026
Perfect match to the one that broke off.
by:
Chris Unger
03/05/2011
extensive emails, and they have the product. need this extra long spring hanger and they were the only ones I could find that had it. Rebuilding a tow behind dump trailer.
by:
David A
09/22/2025
On all points, website, customer service, product quality, and quick delivery etrailer is top drawer!
by:
Timothy
01/21/2026
Great customer service!
by:
Easy to order
10/29/2024
Easy to order the exact part I needed. Paid for next day delivery, but got it in 2 days or would have been 5 Stars.
Wyatt N.
10/30/2025
Exactly the part I needed and it’s worked well
by:
Kyle 2018 Grand Design Reflection 303RLS
08/12/2022
Exactly what i needed. Same dimensions as the original. Might have even been a little thicker gage metal than my originals. I added angle gussets to all my hangers to hopefully keep them from breaking again.
by:
Bones Crandall
04/05/2025
Great service great part and very good communication from the seller!!!!! Highly recommend using them for any and all trailer parts needs they most likely have what most don’t! Thank you trailer your doing great!!!!!
by:
Jim F.
07/09/2017
When I disassembled my springs and shackles to replace the worn items I discovered my hangers were not worn at all. I completed my rebuild of the suspension and had some welding done on the frame that Terry did not complete back in 1996. I ended up using the hangers as barter for a portion of the frame rework.
The suspension parts I used from you folks fit and worked as expected and we took our 1996Tterry 5W to Texas this spring and had a good time.
Thank You,
Jim Ferry
Thornville, Ohio
The suspension parts I used from you folks fit and worked as expected and we took our 1996Tterry 5W to Texas this spring and had a good time.
Thank You,
Jim Ferry
Thornville, Ohio
by:
Bruce Moose
12/22/2016
Parked in the middle of the Mojave desert I noticed that the wheels and tires
on one side of my old Crusader travel trailer were quite close together, within
about two inches of touching each other. On further inspection the welds on the
rear axle spring hanger had failed, leaving 2, 5" pieces of strap steel hanging on
the leaf spring. Was trying to figure out a fix without calling a mobile welding
outfit, when I entered "travel trailer spring shackle" on my Verizon tablet, and
There you and the exact piece of steel I needed were. Had no idea that it was
Such a common part. Cleaned up the frame with a grinder and drilled two
Holes. Two grade 8 nuts, bolts and lock washers. Saved about 15 times the
Cost of the part and shipping. Bravo!!
on one side of my old Crusader travel trailer were quite close together, within
about two inches of touching each other. On further inspection the welds on the
rear axle spring hanger had failed, leaving 2, 5" pieces of strap steel hanging on
the leaf spring. Was trying to figure out a fix without calling a mobile welding
outfit, when I entered "travel trailer spring shackle" on my Verizon tablet, and
There you and the exact piece of steel I needed were. Had no idea that it was
Such a common part. Cleaned up the frame with a grinder and drilled two
Holes. Two grade 8 nuts, bolts and lock washers. Saved about 15 times the
Cost of the part and shipping. Bravo!!
by:
Charley
04/16/2026
Paid $67 for 1 day shipping. Ordered on the 14th wasn’t delivered till the 16th. If there was any problem with that I should have been notified! I’m broke down on the service road south of Dallas. I paid a welder and a mechanic to be there yesterday to install the new part and get me back on the road! Had to pay them again today! Seems like a refund should be generated…
Lazer S.
4/21/2026
Sorry about that, Charley. It looks like your order was placed at 5:05PM (Central time) on the 14th, which is too late for it to go out the same day for next day shipping. That said, I am having the difference between UPS ground shipping and next day shipping credited back to you.
by:
Dave D
09/19/2016
It was just what I needed. Installation was typical. This part replaced a broken one on a fifth wheel trailer. Shipping was great!
by:
Jeffrey
04/01/2013
Perfect match, and the info on the website helped me get the spacing right (factory hangers weren't welded on right so the springs were always cocked)
Jeffrey
4/3/2014
Hi Patrick, still happy as a clam with my order. I took an old camper trailer frame and cut it down to make a canoe kayak trailer. Your info on the web site and parts helped A LOT. We have used the trailer several times. Good stuff. I have 5 trailers, yall are my go to place for parts.
by:
Bob From Detroit
07/08/2017
Everything arrived in a timely manner and was well-packaged.
My only disappointment was not being able to purchase 4-1/4" front hanger brackets in a kit. I was forced to purchase the kit with 3-1/4" brackets and order the 4-1/4" brackets separately.
My only disappointment was not being able to purchase 4-1/4" front hanger brackets in a kit. I was forced to purchase the kit with 3-1/4" brackets and order the 4-1/4" brackets separately.
by:
Larry
03/16/2020
Heavy duty well built straight bends welded nicely. Quality product
Larry
3/17/2021
This is a quality product that goes on straight and true no binding thick and sturdy
by:
Doug S
09/19/2011
somewhere the incorrect label was placed on 2 inch wide spring hangers and the correct appllicationfor the part number is 1-3/4". E-trailer is correcting and providing a shipping label to return the others. Slight delay but sometimes that stuff happens. No worries. The free shipping on $150 orders make up for a lot on heavy parts.
by:
KC
09/02/2020
Perfect fit and no one else had this specific size needed to match my trailer. I would purchase again if the other side breaks an ear off (let's hope not)
by:
Steven
04/27/2018
I try to purchase local when I can but the local trailer places charge from 2 to 4 times what I can get parts from etrailer. So I come to etrailer for all my trailer parts. Service is great and shipping it quick for items in stock. I currently have a few things on backorder that are taking some time.
by:
Charles
09/03/2025
The order was placed on 8/27 I paid for two day delivery. It wasn't delivered until 9/2.
by:
Derek
08/19/2022
The products I ordered came extremely well packed in one large box. The spring hangers look to be in good condition and ready for welding, and the wet bolt kit for Morryde came with excellent instructions. Shipping was quick arriving at my house sooner than expected.
by:
Daniel
08/18/2023
Trailer Doesn't Have broken springs anymore. Fun stuff! Good product, fit properly, no complaints.
by:
John D.
04/22/2013
Great Product...Solid Built. Great Customer Service. Quick Shipping. Would Recommend ETrailer.
by:
Kyle
08/28/2019
The hanger on my trailer was separating from frame. After torching off the old hanger, welding in a support plate- this was a simple replacement. Still holding up well 1 year later.
by:
Darron
10/24/2019
Thank you for all the help on the phone to get the right bracket hanger.
Darron M.
10/25/2020
Product has preformed well no issues
by:
Justin
05/30/2020
Great product worked perfect for replacement on tandem axle trailer. Had a spring perch broken.
25
222
true
Show More Reviews
See what our Experts say about this Redline Trailer Suspension Parts
- How to Get Clearance for Slipper Spring Compressing on Top of Wheel WellTo answer your first question a double-eye spring would not compress less than your current 4-Leaf Slipper Spring w/ Open Eye End # e33SR and I do not recommend going with a higher-rated spring than what your trailer is rated for as that will make your ride very stiff and unpleasant. The only real options you have to get more clearance are to raise the fender if you can or add one that has more height (I have linked our selection of fenders for you to check out) or to cut off your current...
view full answer... - Looking For Angle Braces For Welding To Inside Of Hangers For Additional StrengthHello Pat. We actually used to sell an angled brace from Lippert but it has been discontinued for quite some time. We do not carry one at this time but it was literally just a piece of angled steel. It might not be too hard to make one or find a similar piece of steel that could be used for a brace. I have included some specs from the old Lippert brace I mentioned if you want to take a look and see how you feel about making one.
view full answer... - Replacement Leaf Spring Hanger for 2019 Jayco North Point 315RLTSHello again Greg, did one of your hangers break? You will need to measure to find the right replacement. Your leaf springs are double eye I'm sure, using 9/16" bolts. That only leaves the height as the unknown. See the diagram below, you need measurement "B" to find a replacement. If it is 4-1/4" then the # E4139 you looked at will work. If you have a different measurement, add that in the comments I can see if a replacement is available.
view full answer... - Recommended X-Factor Crossmembers Hey David welcome back! I am not sure what you mean by angled pieces that get welded to the hanger. We have two types of X-Factor Crossmembers and one of them attaches directly to your frame hangers with included brackets and hardware. The MORryde X-Factor Crossmember item # MR33WR attach to standard frame hangers that look like item # E4139. This is most likely what you need. The MORryde X-Factor Crossmember item # MR99ZR works with LRE, RE, or TRE Leaf Spring Suspension. I have linked...
view full answer... - Can Taller Trailer Suspension Equalizer Increase Trailer's Ride HeightYou could do that, but in order to get the height increase, you'll also need to go with taller front and rear spring hangers. For instance, if your current equalizers are 2 inches high, and you switch to the # TREQ310 equalizer which would add two inches, you'd also need a 2 inch taller spring hanger, such as # E4139. If you don't raise the height all the way across the board, the trailer could handle poorly and be more susceptible to sway. If the trailer has a 2-3/8 or a 3 inch diameter...
view full answer... - Lift Kit Adding 2" For 1-3/4" Square Axle 5x8 Trailer.With square axles, neither of our over/under kits will be a fit to raise the height of the trailer so another option is to use longer hangers for the leaf springs. You will just want to confirm the hangar height. You may be able to use a hanger like part # E4139. This hanger is designed for double-eye springs and is 4-1/4 inches tall. The old hangers will need to be cut off and the replacement hangers welded on by a professional.
view full answer...
- How To Lift Trailer with 3-1/2 Diameter 8k Axle With Center Point Suspension Already InstalledYou can lift your 2009 Mobile Suites 5th Wheel trailer, but since you have 8000-lbs Dexter Axles that are 3-1/2" diameter, the Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00 will not work since they are only designed for 3" diameter axles. It's also worth noting that the Lippert Components Center Point Suspension Upgrade # LC1565391 already raises your trailer approximately 2". You could add the Tandem Axle Lift Kit # RR23QX which will add approximately 2-1/4" of lift to...
view full answer... - Will Using Longer Shackle Straps On My Trailer Suspension Affect The Amount Of Travel? By using longer shackle straps it will have an affect on your suspension. For a tandem or triple axle trailer it will move the leaf spring closer to the frame and may cause the leaf spring to contact the frame as the suspension articulates. On a Single axle trailer the larger straps will change the amount of articulation that the spring has. This can have an adverse affect on the suspension components as they do not have a shock to dampen the suspension as it is traveling farther on...
view full answer... - How To Fix Tires Hitting Fenders After Installing New Dexter E-Z Flex EqualizersTo get your Dexter E-Z Flex Equalizer lower so the tires on your 2-17 Nitro Z19 boat trailer are not hitting the fenders I recommend having taller center hangers installed. Base on the pictures you provided it looks like your current hangers are pretty short. You will want to measure from the frame to the center of the hole in the hanger, and then use one of the options mentioned below as a replacement to get the clearance back. The available options are the 3-1/4" tall # 28-5, 3-5/8"...
view full answer...
- Recommendations for Raising Trailer to Add Clearance for Larger WheelsI do have a few possible options for giving your 2004 Toy Hauler some extra clearance for your larger 29-1/4 inch tires. Replacing the Double-Eye Springs and upgrading to a 5 leaf or 6 leaf spring system will provide very minimal rise on your trailer and may not even be noticeable, especially when the trailer is loaded. Additionally, installing overrated springs will create a rough ride as you mentioned but also put extra stress on different components of your trailer when traveling on...
view full answer...
- Recommended Ways To Raise Height Of Small 4 X 8 utility TrailerSince you do not want to use an over/under kit on your axle, the best way to raise the trailer would be to use longer hangers for the leaf springs. You may be able to use a hanger like part # E4139. This hanger is designed for double-eye springs and is 4-1/4 inches tall. The old hangers will need to be cut off and the replacement hangers welded on by a professional. I have attached a link to our product page for the trailer hangers we offer you can check out. If your axle measures 2-3/8...
view full answer... - How To Deal With Axle U-Bolts Making Contact With The Frame Of A TrailerOne thing I recommend doing right off the bat is adding the Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00. This will flip the axle to under the springs and will solve the issue of the U-Bolts making contact with the frame of your trailer. As to the shackles flipping, I think it may actually be a center hanger height issue along with the shackle straps being a little short. If you take a look at the Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt...
view full answer...
- How to Install Spring Hangers on Single Axle TrailerSpring hangers are intended to be welded on. Although you could drill holes in them and bolt them to your trailer, this would affect their capacity to some unknown degree and so this is not recommended. A local trailer supply shop will be able to do this, or there may be an automotive shop near you that is able to do the welding. Since there is not a lot of material to weld, the cost should not be excessive. You may want to review the linked article on trailer suspensions to get a more...
view full answer... - How To Choose the Correct Replacement Trailer Leaf Spring HangerIn order to choose the correct replacement trailer leaf spring hanger you simply need to measure the inside width and length from top to center of mounting hole. The majority of double eye trailer leaf springs will measure 1-3/4" wide so this measurement is not as important as the distance from the top of the hanger to the center of the mounting hole. The Hanger for Double-Eye Springs part # E4139 for example measures 4-1/4" from the top of the hanger to the center of the mounting hole. I...
view full answer...
- How to Raise Trailer Height When Axles are Already Under Leaf SpringsIf you have already moved your trailer axle so that it sits below your leaf springs and you will still have 3" - 4" to go even after adjusting your 5th wheel hitch and pin box the most they can be adjusted then the only thing to do is swap out your hangers. You will need to have a professional welder cut off your current hangers and then you can use taller hangers like the Redline part # E4139 which is 4-1/4" tall. I have linked our selection of leaf spring hangers for you to filter through...
view full answer... - Increasing Clearance Between Frame and Axle on a Boat TrailerAn unloaded trailer should have between 2 and 2-1/2 inches of clearance between the frame and the axle. Typically trailer leaf springs have a maximum deflection of 1-1/2 inches. First, I recommend checking your leaf springs. If they have some age on them, they may have flattened out and need to be replaced. If you find that your springs are still in good condition, there are a few other routes you could take to give yourself more clearance between the frame and axle. If the axle on your...
view full answer... - Can the Center Spring Hanger Be Taller Than Front and Rear Spring Hangers On Magic Tilt TrailerIt is possible to have a center spring hanger that will be longer than the front and rear hangers. For an example I would have the Tandem-Axle Trailer Hanger Kit for Double-Eye Springs, part # APT3HD. This kit has 2-1/2 inch tall front and rear hangers and a 5-7/16 inch tall center hanger. A longer center spring hanger is normally used in conjunction with an equalizer. The equalizers are designed to transfer the load from one axle to another when the trailer goes over a bump. I am including...
view full answer... - Can Equa-Flex Equalizers Add HeightPossibly a bit; it just depends on the height of your current equalizers. The Equa-Flex Cushioned Equalizers - Double Eye Springs - Tandem Axle - 6K to 8K # LC279688 measure 4 inches tall from bottom to top bolt hole, so if you use the same shackle straps and that is quite a bit taller than your equalizer you will add some height. It won't be much though, so if you don't want to add an over/under kit then the next best thing to do is to replace your hangers with taller ones, which can...
view full answer... - Why Do Trailer Center Suspension Hangers Sometimes Hang at Different HeightsIdeally you want the leaf spring to sit as level as possible on your trailer. Since the equalizer used on the trailer can vary in height sometimes the center hanger will set level with the others or it can hang lower depending on the equalizer used. Going with taller hangers in general will lift the trailer and would give you more axle clearance. The hangers should not end up flexing. I attached a link to a page that has a chart at the top that has all of the hangers we carry with their...
view full answer... - Suspension Height on 5th Wheel Trailer with Adjustable Spring HangersUsually leaf spring hangers have one hole on each side to allow the shackle bolt to run through the eye in the spring and then be secured to the hanger, as on a part like # E4139. But if your hangers have multiple holes to allow a choice of trailer height you can certainly use the lower set of holes to lift the trailer relative to the axle. If you refer to the linked diagram you'll see the recommended minimum clearances for 5th wheel towing. 5-1/4-inches of clearance at the bed rails is...
view full answer...
- What is the Inside Width of Trailer Leaf Spring Hanger E4139If the outside width of hanger # E4139 is 2-5/16 inches and the metal thickness is 3/16 of an inch then you would take 2-5/16 and subtract 3/16, and then subtract another 3/16, to get 1-15/16 inches. It is meant to be used with leaf springs that are 1-3/4 inches wide. I made a picture showing these measurements for you.
view full answer...
- Picking Out the Correct Leaf Spring and Spring Hanger Replacements for a Homemade 6x8 Flat TrailerFor a 1,750-lbs leaf spring the closest we carry to what you're needing is the 3-Leaf Double-Eye Spring for 3,500-lb Trailer Axles # e59SR. This spring measures 23-1/8" unloaded, is 1-3/4" wide, and has 3/8" thick leaves. Also, to pick out the correct replacement spring hanger # E4139 you're just going to need to measure the inside width and length from top to center of mounting hole on your current hangers. Most of the time, double-eye leaf spring hangers will measure 1-3/4" wide so...
view full answer...
- Options for Increasing Height of Boat Trailer for Better Ground ClearanceWe do offer round axle over-under conversion kits that will raise a trailer's height. We offer kit # K71-385-00 for 3-inch axle and kit # K71-384-00 for 2-3/8-inch round axles that have double-eye leaf spring suspensions. These allow moving the trailer leaf springs to the top of the axle and give height increases of approximately 4- and 3-inches, respectively. Another option is to install taller spring hangers on the trailer. The linked page will show you all spring hangers for double-eye...
view full answer... - 4-1/4 Inch Tall Hanger Needed for 1-3/4 Inch Wide Double Eye Leaf SpringsWe sure do! What you're looking for is the Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall # E4139 which is designed for 1-3/4" wide springs and the standard 9/16" diameter bolt. Attached is a review video for you to check out.
view full answer...
Do you have a question about this Trailer Suspension Part?
Info for this part was:
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Updated by:
Adele M
Updated by:
Wilson B
Installed by:
Cole B
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Nathan
4/26/2021
After a year and more than six thousand miles under our 30 foot fifth-wheel, these show no sign of degradation. At this point, Ive quit worrying about them, and just keep rolling. Thanks, etrailer!