4-1/4 Inch Tall Hanger Needed for 1-3/4 Inch Wide Double Eye Leaf Springs

Question

Question:

Do you have 4 1/4 spring hangers for 1 3/4 double eye springs?

asked by: John P

1

Helpful Expert Reply:

We sure do! What you're looking for is the Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall # E4139 which is designed for 1-3/4" wide springs and the standard 9/16" diameter bolt.

Attached is a review video for you to check out.

expert reply by: Jon G

1

Answer 1

Since you do not want to use an over/under kit on your axle, the best way to raise the trailer would be to use longer hangers for the leaf springs. You may be able to use a hanger like part #E4139. This hanger is designed for double-eye springs and…

view full answer...

Answer 2

The Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole #E4139 is a weld on application. It hasn't been tested for bolt on installations, so I can't confirm it will hold up if you drilled it and bolted it…

view full answer...

Answer 3

Front and rear suspension hangers are not often the same height like this but they can be. If you have the hanger spacing right then what will happen is the center of the spring will be offset a little between the two hangers to compensate some for…

view full answer...

Answer 4

If you are looking to order a new axle for your 5 foot wide trailer you will need to determine what the hub face to hub face dimension you would need to clear your trailer that is 5 feet (60 inches) wide. You will also need to know the width of your…

view full answer...

Answer 5

When the suspension hangers, equalizers, and shackles are installed from a kit like the part #APT3 the goal is to have the leaf spring as level as possible. The different height hangers is offset by the height of the equalizer and shackles so that…

view full answer...

Answer 6

Since you have only moved things ever so slightly using a longer hanger like the Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall part #E4139 will give you the desired effect and give you the clearance you need. You will want to use…

view full answer...

Answer 7

The tallest front and rear hanger we currently offer is the Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole #E4139 which is only 4-1/4" tall from the center of the bolt hole to the top of the hanger as…

view full answer...

Answer 8

For a 1,750-lbs leaf spring the closest we carry to what you're needing is the 3-Leaf Double-Eye Spring for 3,500-lb Trailer Axles #e59SR. This spring measures 23-1/8" unloaded, is 1-3/4" wide, and has 3/8" thick leaves. Also, to…

view full answer...

Answer 9

The Hanger part #115918 is going to lift your trailer, how much depends on the hangers that you currently have on the trailer. The difference between the height of your current hangers and these will be how much lift you get on the Keystone. We do…

view full answer...

Answer 10

Yes, the front, rear, and center leaf spring hangers can all be the same length. We actually offer kits that come with everything you need including the same length leaf spring hangers for the front, rear, and center. I recommend the Tandem-Axle…

view full answer...

Answer 11

Hello Greg. Generally, yes, shackles are required for any single axle utility trailer. The diagram below will show you the components of a typical single axle setup. You will have shackles on the rear hangers only. This is because as your axle hits…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

4-1/4 Inch Tall Hanger Needed for 1-3/4 Inch Wide Double Eye Leaf Springs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching