See what our Experts say about this etrailer Camper Jacks

• Recommended Flatbed Cargo Trailer Stabilizer Leg for Rear of Trailer
  For your Sure Trac ST9614 HLODOD-B-140 trailer I recommend adding the Ultra-Fab Ultra Scissor Jacks - 24" Lift - 6,500 lbs - Qty 2 # UF48-979002. I believe these will work well to stabilize your trailer for loading. They can be adjusted using the hand crank or you can use the Ultra-Fab Speed Socket Power Drill Adapter for Scissor Jacks # UF48-979005 if you prefer. If you want more of a solid mount drop leg stabilizer that you would weld on, we have the Square Drop Leg Stabilizer Jack...
  view full answer...
  
• Square Drop Leg Stabilizer Jack Tube and Pin Hole Diameters
  Hey D, thank so for reaching out! The Square Drop Leg Stabilizer Jack # SJ-R208 measures 1-1/4" for the tubing on the leg, and it has 7/16" diameter pin holes for the height adjustment. Those holes are also spaced 1-3/16" apart on centers if that helps at all. What do you plan on using this for?
  view full answer...
• Square Tube Stabilizer Jack Needed For An Aluma Tandem Axle Trailer
  Hi Felix, I have two options that might work for your trailer; the first one being the Stabilizer Jacks # TJ01RT-HD. These mount under the trailer and are a bolt on installation. The second is the Square Drop Leg Stabilizer Jack # SJ-R208, which would require welding the channel your frame. Welding to aluminum requires a lot of skill so the cost for this can be pricey. You might want to just weld on brackets to the channel and then bolt that to the frame to avoid the high cost. Do...
  view full answer...
• How Do I Get Part of a Broken Key Out of a Tongue Lock
  Hey, Trevor. I'm sorry to hear that happened. The only Reese lock we carry right now is part # RP7014700, I'm not sure if that is the lock that you got. However, if part of the key is stuck inside the lock, you may need to contact a locksmith, especially if you’d prefer not to cut the lock off. Reese used to offer replacement keys at one time, but unfortunately, they no longer do. A locksmith might be able to remove the broken key and even make a new one. If that’s not an option, the...
  view full answer...
• Will Stabilizer Jack Leg Fit in MaxxTow Adjustable-Height Ball Mount
  I went to take some measurements for you and found the leg of the Square Drop Leg Stabilizer Jack # SJ-R208 measured 1-1/4" outside to outside of the leg itself and 1-1/2" for the mounting bracket. The tube portion of the MaxxTow Adjustable-Height Ball Mount # MT70068 that accepts the ball mount measures about 2-1/2" from outside to outside and 2-1/8" inside to inside. So the stabilizer jack leg would physically fit inside the ball mount; the only issue is that the pull pin from the stabilizer...
  view full answer...
  
• Recommended Weld-On Drop Leg Stabilizers For A UTV Trailer
  We carry a few different weld-on camper jacks to help stabilize your trailer and allow you to easily get your equipment off the trailer. The real question is going to be how long of a jack do you need? The Square Drop Leg Stabilizer Jack - 18" Travel # SJ-R208 you were looking at would work for your needs but we have a few other options that are a bit more compact to ensure you have plenty of clearance. Starting out small we have the etrailer Stabilizer Jacks # TJ01RT-HD, which have a...
  view full answer...
• How To Attach The Square Drop Leg Stabilizer Jack # SJ-R208 To An Aluminum Trailer Frame
  Since welding steel to aluminum can be a hassle the easiest option would be to get a steel plate that you could just bolt to the aluminum frame and welding the Square Drop Leg Stabilizer Jack # SJ-R208 to the steel plate. Other than that you'd be looking at a very expensive weld job using a dip-coating process.
  view full answer...
• Stabilizer Jacks For Rear End Of Enclosed Cargo Trailer.
  Great question. Without cutting a hole you wouldn't be able to get enough clearance for the jacks to work. I would strongly recommend using them on the outside to prevent clearance issues and probable damage. However, I think you would be better off going with the Stallion Stabilizer Jacks - 7" Drop Leg Travel - 22-1/4" - Qty 2 # 288-01892-2 you can mount them underneath and then they can fold up and out of the way.
  view full answer...
• Types of Jacks Suitable to Stabilize Equipment Trailer During Loading
  We have various jack and stabilizer products that you can consider for addition to the rear of your equipment trailer to support it during loading processes. I linked our main page for such items so you can see all we offer. If you want a low-cost and lightweight option that does not require permanent installation you might look at the Ultra-Fab Stackable Stabilizers # UF48-979003 (a set of 2) or the 4-piece set # UF48-979004. These offer 17-inches of lift and the 4-piece set weighs only...
  view full answer...
• Best Way to Stabilize Back of Trailer When Loading a Tractor
  For your application I recommend installing the Square Drop Leg Stabilizer Jack # SJ-R208 which is a weld-on application that provides 18" of travel and a 2,000 lb weight capacity. To stabilize your trailer you basically need something to take up the space between the ground and your trailer frame which is what jacks are designed for. Anything else is meant just to stabilize a load or it would be something like load leveling blocks that you'd have to store and then place down prior to loading...
  view full answer...
• Outer Tube Dimensions of the Square Drop Leg Stabilizer Jack SJ-R208
  The outside dimensions of the outside tube of the # SJ-R208 measures 1-1/2 inch by 1-1/2 inch. The overall length is 8 inches. The outside dimensions of the inner leg are 1-1/4 by 1-1/4 inch. For more info and more dimensions check out the review video I attached for this as well.
  view full answer...
• Where is the Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs Made
  The Square Drop Leg Stabilizer Jack part # SJ-R208 is made overseas but it does have a warranty so if there were any issues with this product you'd be covered. That said, there really isn't much that could fail on the stabilizer so how it's attached to the trailer is likely going to be the weak point. Unfortunately, we don't offer any domestically made stabilizer jacks in this style.
  view full answer...
• Replacement For Fulton Drop-Leg Stabilizer Jack
  For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs # SJ-R208 Different manufacturers but otherwise they are the same, as the Fulton and the # SJ-R208 are both 20" tall, with a mounting plate that is 8" long x 1-1/2" wide, and a 2,000 lb capacity.
  view full answer...

Do you have a question about this Camper Jack?