To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Get a brake controller in your truck that looks like it's supposed to be there. This sleek knob blends right into your dash and makes your settings simple and convenient to adjust.
Features:
Specs:
Note: The main unit must be mounted horizontally level and parallel to the direction of travel within 20 degrees.
Power output: To get more power output - the maximum amount of power that will be applied to your trailer's brakes - rotate the knob clockwise. To decrease the power output, rotate it counterclockwise.
Manual override: To engage manual override, simply press the knob. This will activate the trailer's brakes and brake lights independent of your tow vehicle, great for stopping sway or controlling your trailer's momentum in an emergency. The Voyager iD will reach the maximum set power in half a second.
The Voyager comes in 2 pieces: the main unit and the control knob.
The control knob can be installed in any convenient spot that's easy for you to see and access. This can be a blank switch panel, an open spot on your center console, or wherever there's space on your dashboard. Before you do any drilling, be sure there's enough clearance behind the dash for the entire knob to install!
Once you've decided where you want to put the control knob, you'll need to find a good place to install the main unit. It needs to be horizontally level and parallel to the direction of travel within 20 degrees. A mounting kit with hardware is included.
This kit comes with a vehicle-specific wiring harness that plugs right into the factory port beneath the dash of your vehicle. That means no hardwiring!
You will also need a circuit breaker kit to complete your installation:
Note: If you don't already have a 7-way plug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately).
Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Voyager iD uses an internal inertia sensor to sense how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to review part number 3021-P. This is the Tekonsha Plug-In Wiring Adapter for the Draw Tite and Tekonsha Electric Brake Controllers. This is a custom fit part number. It is designed to fit the 2010 to 2012 Dodge Ram and Ram 1500, 2500 Heavy Duty and 3500 Heavy Duty Trucks. This wiring adapter will make it easy to install your electric brake controller on your vehicle. One end here has the custom connector end which will plug into your built-in brake controller port on your vehicle, usually located beneath the dash of the vehicle. The other end is the flat, black plug.
This plugs into the back of your Tekonsha Electric Brake Controller. This wiring harness is compatible with the time delayed brake controllers by Draw Tite and the proportional brake controllers by Tekonsha like the Prodigy, Prodigy P2, P3, the Primus IQ and the Voyager. Basically the way you would install this, I've got an example here, a Prodigy P3. We do sell this separately on our website, it's part number 90195. If you look on the back you can see the plug in for the black connector. If we just push it on it'll lock right into place. Then you just take the other end with the grey custom connector on it.
This will run underneath your dash and plug into the factory brake controller port on your vehicle. Once it's all connected in then you're ready to go. When you need to remove your brake controller all you need to do is lift up on your connector and it will slide right off and disconnect. That should do it for the review on part number 3021-P. This is the Tekonsha Plug-In Wiring Adapter for the Draw Tite and Tekonsha Electric Brake Controllers. .
Easy install simple setup
Everything worked as it should! Very happy with the look as well
Works good
The install was pretty simple. It took some time to modify the knock out plug to conceal the adjustment knob but after a bit of work it fit nicely and looks like it’s supposed to be there. I missed a photo of the final mont of the control unit but I was able to install the supplied clip for the module just above the airbag. There is a clip that holds the wire for the computer input so I removed it for extra space and secured the wire with a zip tie.
Works great. custom harness makes it plug and play!
Easy install. I used the cable harness that came with my 22 Silverado. Hardest part was just locating a place on the dash for the knob and access from behind for the 2 inches or so length of the switch assembly. Small and looks good on the dash.
Perfect fit
Makes the job a snap. Literally.
perfect fit easy install
Great product and very fast shipping.
Item arrived on time, perfect fit
Great service, great buying experience.
Perfect match. Quick delivery.
Great Form Fit and Function
Perfect fit-works great
IT'S A GREAT CABLE AND IT PLUGS RIGHT IN JUST LIKE A CABLE SHOULD
The Tekonsha Break controller works great, and was easy to install.
so simple an makes for pain free hook up!
Plug and play - 10 second install (if you're sorta "slow").
Do you have a question about this Trailer Brake Controller?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.