To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
These strong, galvanized steel crossbars supply the backbone for this Yakima roof rack. The rack works with accessories that clamp around the bars. Vinyl coating helps resist corrosion. Installs to the rain gutters on your vehicle's roof.
Features:
Specs:
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Adam: Hi everyone, Adam with etrailer.com. Today we're going to be taking a look at the Yakima round bar roof rack system on our 2017 Chevy Express.This is going to be a great addition to your Express van just because obviously we're going to be able to fit quite a bit of passengers in here, and it's always nice when you're going on vacation and you have a lot of room just to kind of relax on the long drives you may be taking, so luckily we can put either all the gear that they may have with a cargo basket or a cargo box up on top of here, or if you want to carry all your canoes, kayaks, or even a decent amount of bikes you can put them up here as well just so all your passengers will be nice and comfy.These are the 66" round bars that we have on top of our Express van here. They are made of steel with a nice powder coated finish, so they are going to resist against rust and corrosion over time. Also they will have a weight capacity of 165 pounds, but make sure that your Express van can handle that kind of weight.Honestly, with 165 pounds you can use these yes, for all the recreational stuff you may be doing on your vacation, but also for work. You can throw lumber up here, drywall, even a couple ladders. All you got to do is just make sure it's tied down properly and then you're ready to hit the road.So let's do some measurements for your guys.
From our roof to the bottom of our bar we are going to have about 4-3/4", and from our roof to the top of the bar it's going to be a little bit underneath 6", so we're going to have plenty of room to be able to fit even some of those attachments that are going to wrap underneath and around these bars. Even if they are bigger mounting hardware we don't have to worry about it rubbing against our roof.It is relatively easy to install on the roof, so let's just go ahead and show you how. Okay, so the first thing we want to do is we're going to have this little lip here. It's made of plastic. You get a little rubber boot and all you really need to know is you see this little dip right here That's going to be facing up towards our tower.I found it easiest to kind of like just spread it out and get that hole going and then kind of pull it a little bit.
I'm going to have to push that top lip up. Then you do the same kind of thing to the other side. Just make sure it's nice and tight and just flush with this lip. You're going to have to mess with it a little bit to get it to fit on there really good.So now that we have that installed, we are going to want to loosen this bolt here on the underneath. There is a tool included, but once you get it loosened most of the way you can actually just kind of rotate this assembly and that's going to allow our bars to be able to slide in there, because when we tighten it down it's going to push this little black piece up to lock the bar into place.So we're going to take it and this lip that we put the boot on is actually going to sit in this little divot here on the roof.
Seat it down into that little groove there. Then of course this metal part is going to be underneath this lip here.So we can either go ahead and grab the bar or just place it on the other side. If you have a specific bar width that you want to meet, definitely measure all that out. I'm going to put it about here, and I'm going to go grab our round bar.Okay, so you see how these towers are kind of facing inward That is the orientation that we want on both sides, and of course we want those facing the same way as well. This is not right and this is correct.
So that's something to keep in mind. If you have the caps on your round bar already installed, you're going to have to remove them, and I'm actually going to start with this one here. Slide it all the way down. Grab our other one. This might be a little bit easier with an extra set of hands, but I'm going to see if I can get it done all by myself.So now with those on our bar we can gently lay it down, trying to get it into the right spot. If you get one side kind into place you can just kind of lay it down a little bit and then go and fasten and get the other side kind of into place, and then we'll go ahead and fasten them all down.This wouldn't be a bad time to get the measuring tape out, making sure that the distance between the towers on this side and the distance between the towers on that side match.Sometimes if you have a more bubbly roof this bracket that hooks underneath this lip on the back side, it might be rubbing against your roof. We do have extra little rubber bumpers here, so if we are having that issue we can actually just put that on the backs of the bracket to prevent any wear to your paint, but in this instance we are not having any of those issues, so we won't be using them.The next step, we have a little push knob here. It's going to thread into our tower, and as we thread it in it's going to pull the top part of this metal section here back towards the tower, so then the bottom part is going to go into that groove, giving you a secure fit. As you can see, it's doing its thing. You're going to have a decent amount of turns. That should get it pretty tight. Give it a good wiggle. Then you can go ahead and do the same thing on the other side.One thing I do recommend getting is you can get some locking cores so someone can't just come up to this and just undo it and grab your roof rack and run off with it. We do sell those separately at etrailer.com, and you'll get keys with your kit just to give you that added protection.So before we fasten down our round bars here so they're nice and tight we're going to use the fact that they're loose to just make sure that they're even on both sides. You can kind of twist and get them nice and even. You can grab a tape measure if you want, but if you have them where you want them, which I do, you can go ahead and take that same tool that we used to loosen up the bolt and we can actually go ahead and tighten it. So now the only thing we have left to do is install our caps.Well everyone, that's just about all you really need to know about the Yakima round bar roof rack system on our 2017 Chevy Express.
Asadvertised.
Heavy Duty bars .
Great product and great service.
great racks
Good Product Easy Install Thank You
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.