See what our Experts say about this CURT Pintle Hitch

• Pintle Hitch Plate For 1997 Ford L8000 Dump Truck
  The only option we have for a pintle hook plate that has D-rings attached for the 1997 Ford L8000 Dump truck is the fabrication plates like part # 3371809042 part # 3371809043 and part # 3371809040. These plates come with the D-rings to be welded on with additional gussets for strength. Then you would use Buyers Pintle Hook with Mounting Kit - Bolt On part # 33710042. We do not currently carry anything that is truly adjustable for the dump truck unless you have a 2" hitch. Then you could...
  view full answer...
• Can B&W Pintle Mount and Tow Ready Pintle Hook Give 4 inches of Drop
  Yes, if you used the Pintle Mount part # BWPMHD14005 that you referenced with the 20k Pintle Hook part # C48210 you'd easily be able to get the 4 inches of drop you need. Both of these components have well over the 13,500 lb capacity you are in need of so they will work well in that regard as well.
  view full answer...
• What are the Torque Specs for the Curt Pintle Hook C48210?
  Hey Ryan, welcome back! The Curt Pintle Hook item # C48210 includes 4 four 1/2" grade 8 bolts that need to be torqued to 90 ft-lbs. This pintle hook has a 20,000 lbs capacity and is compatible with 2-1/2" and 3" lunette rings. What kind of trailer are you pulling? You can add this information and any other questions you have where it says Reply to Jerred H and I'll be happy to answer them.
  view full answer...
• Buyers Products 3 Position Pintle Hook Mount Rise When Using Top Holes
  Hey Darin! You can expect approximately 2-1/2" of rise using the top holes of the # 337PM25812 in the rise position. There can be some variation depending on what attachment you use like the # C48210. If you have any other questions feel free to reach out in the comments below.
  view full answer...
• Recommended 3 Inch Lunette Ring Over 2-1/2 Inch Alternative
  The standard size lunette ring is 3 inches like the Demco Lunette Ring - Adjustable Channel Mount - 3" Diameter - Black - 25,000 lbs # DM09557-81. The 2-1/2 inch rings will not fit in the adjustable channel mounts where the vast majority of the 3 inch rings are designed for that style application. All of our pintle hooks like # C48210 are designed to work with the 3-inch lunette ring. There will be some movement, but there is not excessive slop. There needs to be some movement with...
  view full answer...
• Recommended Pintle Hook And Mount With 8 - 10 Inch Rise
  If you have a 2 inch receiver opening on the vehicle you will be towing with the B&W Pintle Hook Mounting Plate, part # BWPMHD14005 may work well for you. The mounting plate features 7 holes on each side of the plate that are spaced 1-3/4 inches center to center and the space between the two rows of mounting holes are spaced 3-3/8 inches center to center. The weight capacity for this mount is 16,000 lbs. The distance from the center of the hitch pin hole to the mounting plate is 12-1/8...
  view full answer...
  
• Need Adapter to Mate Military Trailer With Standard 2-Inch Hitch Ball
  Often military trailers use a pintle or clevis type hitch. The link provided at right will take you to our main page for ball mounts where you can see both types. You can submit a photo to us to show your military trailer's hitch by responding to this email or by uploading your photos with a question. Please be sure to provide complete information on both the trailer and vehicle. For example, we offer mating pintle type parts # 63036 and # C48210.
  view full answer...
• Recommended Adjustable 2 Ball Coupler To Replace A Lunette Ring On A Trailer
  If you are replacing your current lunette ring, you will need to check on 2 measurements to make sure a coupler will fit your channel. First will be the width and second will be the hole spacing. As an example, the Demco Trailer Coupler - Adjustable Channel Mount # DM12688-95 will fit a 3" wide channel and will have 2" hole spacing when measured center to center. This is also designed for the use with a 2" ball and will have a 10,000 max capacity. Odds are this will match what you have...
  view full answer...
  
• Is There A Pintle Adapter Available For A B&W Tow And Stow Ball Mount In A 3 Hitch
  Though I may have another option available for you, the B&W Tow & Stow 3-Ball Mount # BWTS30049B is not available with a pintle hitch as of yet. With that being said, there are actually no current options available for the 3" hitches being used, so you will need to use a reducer, like the # 58552, if you do not already have one. This will allow you to go one of two ways. First will be the Curt Pintle Hook with 2-5/16" Ball - 2-1/2" Hitches # C45908. This is rated to 20,000 pounds and...
  view full answer...
• Can a Swivel Type Pintle Hook Be Used with 2 Hitch
  The best option I have for an adjustable pintle hook that slides into a 2" hitch is the Curt Pintle Hook Mounting Plate part # C48341 with the Curt Pintle Hook part # C48210. I am not aware of any way to use a swivel type pintle hook with a 2" hitch. That said, you might be interested in Lock-N-Roll system, like part # 336TS528 and part # 336VS501 which would give you the swivel feature and 2" hitch compatibility.
  view full answer...
• Recommendation For Pintle Hitch To Work With 3-Inch Lunette Ring On 10-Ton Trailer
  Yes, the Curt Bolt-On Pintle Hook, Item # C48210, will work with a 3-inch lunette ring on a 10-ton trailer. It has a maximum weight capacity of 20,000-lbs and a maximum tongue weight capacity of 4,000-lbs. The mounting hardware is included, and it can be bolted to a pintle hitch mount or directly to a reinforced utility truck bumper. If you need a similar pintle hook with greater capacity, I recommend the Curt Bolt-On Pintle Hook, Item # C48215, that has a maximum weight capacity of 30,000-lbs...
  view full answer...
• Can Buyers Products 3 Position Pintle Hook Mount be Used in Rise Position
  Yep, you can absolutely use the Buyers Products 3 Position Pintle Hook Mount for 2-1/2" Receiver # 337PM25812 in the rise position instead of the drop position. This is a 20k mount that will go perfectly with a pintle hook like the Curt Pintle Hook # C48210 with Mounting Kit # 3378520.
  view full answer...
• Mounting Hole Spacing on B&W Pintle Hook Mounting Plate BWPMHD14005
  I went to our warehouse and measured the B&W Pintle Hook Mounting Plate # BWPMHD14005. I measured the center to center horizontal hole spacing at 3-3/8-inches so it will work well with Pintle Hook # C48210.
  view full answer...
• Pintle Hook Mount and Pintle Hook Recommendation for Pulling a Military Trailer With a Chevy Tahoe
  The pintle hook mount that I would recommend for you is the Pintle Hook Mount, 12-1/2 inch Tall, 8K, part # 63058. This hook mount has an adjustable rise that will go up to a 12 inches. That would put the height of your pintle hook mount right at 31 inches if it was in the highest possible position. This hook mount has a tongue weight capacity of 800 lbs and a total weight capacity of 8000 lbs, you will want to check that against the weight of your trailer to make sure its not too much...
  view full answer...
• Will a Pintle Hitch Fit Weld-On Nose Plate 337TNP716625750
  Plate # 337TNP716625750 is going to be larger than what pintle hook # C48210 requires. The pintle hook is usually on the vehicle side so the mounts for it all have regular shanks that fit a hitch receiver. You want something like part # 63057. The nose plate would be used on the trailer side to attach a lunette ring such as # C48550. The bolt holes are 4-1/2 inches apart.
  view full answer...
• What is Needed for a Pintle Hook for a Ford F-250 Super Duty to Tow a Trailer Level
  You will want a pintle hitch or any ball mount on a vehicle at the appropriate height to tow the trailer level. To do this you will need to park the vehicle and trailer on level ground and take some measurements. I have included a link to an FAQ article that will help. On a pintle hitch you would need to measure from the ground to opening on the hook part and on the ring measure from the ground to the bottom of the ring. Once you know the rise or drop you need what you can do is get an...
  view full answer...
• Pintle Hook Recommendation to Fit B&W Pintle Hook Mounting Plate # BWPMHD14002
  The Curt pintle hook part # C48210 has a 20k capacity and would mount up to the mount part # BWPMHD14002 that you referenced. This would be a great option that would work well.
  view full answer...
• Higher Rated 2 Inch Pintle Hook Mounting Plate
  Both parts # BWPMHD14005 and # BWPMHD14004 have a tongue weight capacity of 1,600 pounds. Part # C48210 has a tongue weight capacity of 4,000 pounds. So using that hook with either of those two mounts limits you to the lower 1,600 pound capacity. For a higher rated mount the Buyers Products, part # 337PM1012, has a tongue weight rating of 2,000 pounds.
  view full answer...
• Length From Pin Hole To Face of Curt Pintle Hook Mounting Plate C48348
  The distance from the mounting face to the hitch pin hole is approximately 7 inches for the Curt Pintle Hook Mounting Plate for 2-1/2" Hitches # C48348. With this plate you can use a pintle mounting hook with 9/16" mounting holes, such as the Curt Pintle Hook # C48210. I have added links to video reviews for you to check out as well.
  view full answer...
• Pintle Hook for a 2-1/2 Inch Trailer Hitch with a Long Shank
  If you are just looking for a standard pintle hook without a ball then I think the Curt Pintle Hook part # C48010 will be the best option we have for you. This pintle hook has a 2-1/2" shank and measures 9-1/2" from the center of hitch pin hole to the center of pintle hook. It has a 20,000 lb towing capacity. If you need something with a longer shank then you will need to look into a two piece unit like the Curt Pintle Hook Mounting Plate part # C48340 with the Curt Pintle Hook part #...
  view full answer...
• What is a Pintle Hitch
  A pintle hitch is primarily used in heavy duty towing situations. The hitch itself resembles a hook that can be closed around the lunette ring that is mounted on the trailer. Part # C48210 is a good example of a pintle hook. The pintle/lunette combination is typically used on construction or other heavy duty equipment.
  view full answer...
• Buyers Products 2 Pintle Hook Mount # 337PM90 Come with Mounting Hardware
  Buyers Products 2" Pintle Hook Mount # 337PM90 does not come with hardware to mount a pintle hook to it. Some of the pintle hooks come with hardware, such as Curt model # C48210. Or if you just need hardware you can use # C48330.
  view full answer...
• Can the Gen-Y Torsion Pintle Hook Mounting Plate for 2" Hitches Be Mounted In the Rise Position?
  Yes, you can mount the Gen-Y Torsion Pintle Hook Mounting Plate for 2" Hitches item # 325-GH-1201 in either the rise or drop position. It will either give you a maximum drop of 5-1/2" or a rise of 5-1/2". It will be taller if you mount it in the rise position. It has six mounting positions that let you customize the height of the pintle. This ball mount has a 16,000 lbs capacity and a built in tongue weight scale that shows if a load needs to be adjusted. You will want to use either the...
  view full answer...
• Can the B&W Pintle Hook Mounting Plate be Used in Both the Rise and Drop Positions
  The B&W pintle hook mounting plate # BWPMHD14004 can be used in the rise or drop position and the capacity remains the same. It is rated for 16,000 pounds gross trailer weight. For a bolt-on pintle hook you can use # C48205 which is rated for 10,000 pounds so you would be limited to that 10,000 pounds. The hardware that you need to bolt it to the mounting plate is included. For a higher capacity pintle hook use # C48210. It is rated for 20,000 pounds but you would be limited to the 16,000...
  view full answer...

Do you have a question about this Pintle Hitch?