Pintle Hook Recommendation to Fit B&W Pintle Hook Mounting Plate # BWPMHD14002

Question

Question:

do you offer a pintal hook without the ball that will match up to the weight capacity of this plate ? , if you do, does the hole mounting patterns match up also ?

asked by: Charlie S

0

Expert Reply:

The Curt pintle hook part # C48210 has a 20k capacity and would mount up to the mount part # BWPMHD14002 that you referenced. This would be a great option that would work well.

expert reply by: Jameson C

0

Answer 1

We do indeed have that particular fender clearance/marker light, we refer to it by our part number, which is #OPT36FR.

view full answer...

Answer 2

The bolt hole pattern center on center for the Curt Trailer Hitch Receiver #13018 is 3-1/4 inches horizontally and 2-1/4 inch vertically. This varies from the 3-3/8 inch horizontal and 1-3/4 inch vertical measurements that a typical Pintle Hitch,…

view full answer...

Answer 3

The standard size lunette ring is 3 inches like the Demco Lunette Ring - Adjustable Channel Mount - 3" Diameter - Black - 25,000 lbs #DM09557-81. The 2-1/2 inch rings will not fit in the adjustable channel mounts where the vast majority of the 3…

view full answer...

Answer 4

I had the bolt holes on the Super Titan Forged Pintle Hook Plate for 3" Trailer Hitches #RP38186 measured, and they are actually 5/8". That being said, I suggest going with the Curt Pintle Hook #C48215 to attach to it. This does include 1/2…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Pintle Hook Recommendation to Fit B&W Pintle Hook Mounting Plate # BWPMHD14002

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching