Wiring Diagram for the Replacement Electric Jack Switch with Harness # LC387874

Question

Question:

Do you have a wiring diagram for this switch

asked by: Tom

0

Expert Reply:

Yes, I have attached the wiring diagram of the Replacement Electric Jack Switch with Harness # LC387874 for you to reference. Basically the Blue wire goes to a 6A auto reset breaker, like part # LC134181, which then goes to the positive circuit for extending, the Yellow goes to the positive circuit when retracting, the Red wire goes to the positive battery terminal, and the Black wire goes to the negative battery terminal.

expert reply by: Jon G

0

click to enlarge

Anibal

7/24/2024

Hi Jon. I have a Lippert smart jack on which the "smart" components got wet and ceased to function. I bought a simple extend/retract switch and bypassed the "smart" components. It works but keeps blowing a 6A fuse that I put between the blue wire and the red motor power wire. It's just a regular fuse, not like the auto reset one that you illustrate here. My question is, is this fuse needed and, if so, why? It didn't have one before. Thanks, Anibal

Reply

Jon G.

7/24/2024

@Anibal I haven't taken apart the Lippert Smart Jack # LC643589, but if there wasn't a fuse to begin with then you should be fine. Fuses are a good safeguard to keep from having to replace something more expensive if it gets too much power. As long as your bypass work isn't going to be overloading anything then the fuse you added won't be needed.

Reply

Anibal

7/24/2024

@JonG Thanks Jon. I ended up putting a 15A fuse in the holder and, so far so good. Appreciate your prompt response!

Reply

Jgh

2/1/2025

Hi could I use a dump trailer remote switch it has the up and down with 4 wires

Reply

Jon G.

2/3/2025

@Jgh You can certainly try it and see. I would say make sure you have circuit breakers in the appropriate locations to make sure everything is protected prior to trying this out though.

Reply

Rene L.

4/9/2025

Hello. What is the white ground wire doing on the switch?

Reply

Jon G.

4/9/2025

@ReneL Not going to lie, I'm a little confused by this question. If you have a white ground wire then you'll want to ground it for proper function... If you're referring to the diagram above, there is no white wire in the diagram, but the Black ground wire is connected to the negative battery terminal in this case.

Reply

Rene L.

4/9/2025

@JonG Hi Jon, regarding above question, white ground wire is going to one of the 4 terminals on my up/ down momentary 4 wire switch. The opposite terminal has the power ( red) wire. 3rd terminal is power down, 4th terminal is power up. What is the white grounded wire’s function? Thanks. and sorry for the confusion.

Reply

Jon G.

4/10/2025

@ReneL The white ground wire's function will be to provide a ground for the electric setup. If you notice in the diagram on the answer page above, this switch has a ground wire as well. All electrical components require a ground to work properly, so you'll want to make sure your white ground wire is connected either to the negative terminal on your battery, or a bare-metal surface on your trailer frame. It's best to follow the instructions from the switch manufacturer. If you don't have those then I recommend wiring your switch up to the same connections your old switch was connected to.

Reply

See All (5) Replies to Rene L. ∨

Answer 1

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Answer 2

The MaxxAir Replacement RV Air Conditioner Cover for Coleman-Mach / RVP Brand RV Air Conditioners part #MA8335A5261 is a direct replacement for the original cover on your Coleman Mach AC unit. This option offers the best value for you and has equal…

view full answer...

Answer 3

For a replacement Advent unit for your Coleman Mach, I suggest the 15,000 Btu Advent Air Replacement RV Air Conditioner for Coleman Setup w/ Start Capacitor, #ACCOL150B for black cowling or #ACCOL150 for white. These options are designed to replace…

view full answer...

Answer 4

Unfortunately, there isn't a direct replacement, however I recommend going with the Furrion RV Tankless Water Heater #FR93FR with the conversion kit #FR73FR for white or #FR63FR for black. This unit requires a 12-5/8" wide x 12-5/8"…

view full answer...

Answer 5

On the Lippert Power Stabilizer Jack #LC298707 for your Forest River Evo Trailer Trailer there should be a 20 amp (or higher) fuse/breaker located inline with the red power wire coming from the switch before it reaches the battery. Check to make sure…

view full answer...

Answer 6

The Replacement Auto-Programmable Controller Panel #LC26TF is the correct replacement for your current Lippert part 366701. I got this information directly from Lippert.

view full answer...

Answer 7

If you take a look at the diagram I've provided for the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW which goes to the Electric Jack w/ Footplate #EJ-3520-WBX, you'll be able to see how both of the…

view full answer...

Answer 8

Hello Jason. Thanks for reaching out. We do have a few options for the vinyl RV flooring, although it doesn't look like we have anything in a wood color. What we have will be either black, gray, white or a checkerboard pattern. I have provided a…

view full answer...

Answer 9

To replace the Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD you'll just need to keep track of how the original was hooked up and replicate that. Unfortunately Lippert doesn't have a wiring diagram but we do have a photo we…

view full answer...

Answer 10

Yes, they do. The Blue Ox Sway Pro item #BLU54TR and item #BXW2003 are a couple of our most popular weight distribution systems that include the 2-1/2" shank. If you already have a weight distribution system, or want to go with a different…

view full answer...

Answer 11

We have the 12k rated Equal-i-zer part #EQ37121ET which comes without a shank so that you could add the shank you'd need like the part #EQ90-02-4700 which fits a 2-1/2 inch hitch and has a 3 inch drop or part #EQ90-02-4900 which can do a 6 inch…

view full answer...

Answer 12

If you are using either the Lippert Components Landing Gear Switch #LC145236 or the Stromberg Carlson Landing Gear Switch #LG-145236 you will connect the red wire without the fuse along with the longer black wire to the red and black wires on your…

view full answer...

Wiring Diagram for the Replacement Electric Jack Switch with Harness # LC387874

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching