Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x…
Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and…
The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…
The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Buick Regal AccessoriesSelect A Category Below
Towing
Buick Regal Trailer Hitch
Buick Regal Trailer Wiring
Buick Regal Brake Controller
Buick Regal Base Plate for Tow Bar
Buick Regal Vehicle Tow Bar Brake System
Buick Regal Vehicle Tow Bar Wiring
Buick Regal BOLT brand vehicle and hitch locks
Cargo Control
Buick Regal Roof Rack
Buick Regal Trunk Bike Rack
Performance Accessories
Buick Regal Air Filter
Buick Regal Exhaust
Buick Regal Suspension Enhancement
Buick Regal Transmission Cooler
Buick Regal Performance Chip Tuners
Buick Regal Vehicle Lights
Buick Regal Tire Chains
Buick Regal Fluid Filters
Buick Regal Catalytic Converters
Buick Regal Vehicle Engine Heaters
Buick Regal Radiator Fan
Buick Regal Cabin Air Filter
Buick Regal Lift Assist
Vehicle Trim
Buick Regal Floor Mats
Buick Regal Vehicle Covers
Buick Regal Side Window Vents
Buick Regal Vehicle Seat Covers
Buick Regal Replacement Mirrors
Buick Regal Windshield Wiper Blades
Buick Regal Windshield Covers
Buick Regal Vehicle Air Mattress