Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
I&…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure…
Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…
Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Chevrolet Camaro AccessoriesSelect A Category Below
Towing
Chevrolet Camaro Trailer Hitch
Chevrolet Camaro Trailer Wiring
Chevrolet Camaro Brake Controller
Chevrolet Camaro Base Plate for Tow Bar
Chevrolet Camaro Vehicle Tow Bar Brake System
Chevrolet Camaro Vehicle Tow Bar Wiring
Chevrolet Camaro BOLT brand vehicle and hitch locks
Cargo Control
Chevrolet Camaro Roof Rack
Chevrolet Camaro Trunk Bike Rack
Performance Accessories
Chevrolet Camaro Air Filter
Chevrolet Camaro Exhaust
Chevrolet Camaro Suspension Enhancement
Chevrolet Camaro Transmission Cooler
Chevrolet Camaro Performance Chip Tuners
Chevrolet Camaro Vehicle Lights
Chevrolet Camaro Tire Chains
Chevrolet Camaro Fluid Filters
Chevrolet Camaro Catalytic Converters
Chevrolet Camaro Vehicle Engine Heaters
Chevrolet Camaro Radiator Fan
Chevrolet Camaro Cabin Air Filter
Chevrolet Camaro Lift Assist
Vehicle Trim
Chevrolet Camaro Floor Mats
Chevrolet Camaro Trim Kits
Chevrolet Camaro Vehicle Covers
Chevrolet Camaro Vehicle Seat Covers
Chevrolet Camaro Replacement Mirrors
Chevrolet Camaro Windshield Wiper Blades
Chevrolet Camaro Windshield Covers
Chevrolet Camaro Vehicle Air Mattress