Replacement Spindle For 1995 Calkins Boat Trailer
Updated 12/15/2025 | Published 11/12/2024
Products Featured in This Question
Question:
Hi. This concerns my Calkins boat trailer, TFY-18-2000, mfg. 7/95. I cant seem to keep the water out of the hubs. Im thinking maybe because the the surface where the axle seal rubs is pitted. I can send pics. Heres more info: Capacity: 2000lbs Hub face: 73-1\8 Bolt pattern: 5 on 4-1\2 Spring center: 59-3\8 No Idler hubs Leaf Springs Axle diameter: 1-7\8 Axle length: 78-1\8 Does Etrailer have options for me? I can send pics. Thanks, Lowell
asked by: Lowell B
Expert Reply:
Hi Lowell; since you're looking at # TRU97FR I'm assuming you want to replace the spindle. If it is pitted out where the grease seal rides I would say that is the reason for the water. The replacement spindle will depend on the bearings you have. This BT8 spindle is for # L44643 (1.00" inner diameter) inner and outer bearings. If you have # L44649 (1.063" inner diameter) you need a BTR # TRU44FR.
You may be better off replacing the entire axle if you can find one that matches. We do not carry a 2k axle with those measurements so you I would check with an axle manufacturer like Dexter to see if this is something that is available.
You may also want to consider adding Bearing Buddies as well to help keep everything sealed up and protected. The right Bearing Buddy depends on your hub bore measurement. I attached a link to all of our available Bearing Buddy Bearing Protectors below which can be filtered by hub bore diameter for your reference.
Product Page this Question was Asked From
Square BT8 Spindle for 2,000-lb Trailer Axles - 1-1/2" Wide
- Trailer Spindles
- Standard Spindle
- Without Flange
- L44643
- 1-1/2 Inch Diameter
- Square
- For 2000 lb Axle
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: bearing l44643 trailer bearings races seals caps
- Search Results: bearings trailer bearings races seals caps
- Search Results: l44543
- Search Results: trailer hubs and drums
- Search Results: license plates bracket
- Search Results: heat shrink connectors
- Search Results: leds trailer lights
- Article: Most Popular Wheel Bearings
- Article: Trailer Wiring Diagrams
- Video: Installing the etrailer Easy Grease Trailer Idler Hub Assembly
- Video: All About the Deka Heat Shrink Butt Connector
- Shop: Trailer Hitch
- Q&A: Replacement Hub w/ a 5 on 4-1/2 Lug Pattern and L44643 Inner and Outer Bearings
- Q&A: How to Determine What the Correct Replacement Hub Is
- Q&A: Possible Solution for Replacing Trailer Bearing L44543
- Q&A: Are Taillights STL8RGB and STL9RGB a Set? What Butt Connectors and Shrink Wrap do I Need?
- Shop: Kenda Karrier S-Trail ST145/R12 Radial Tire w/ 12" Galvanized Spoke Wheel - 5 on 4-1/2 - LR D
- Shop: Replacement Trailer Wheel Bearing - L44643 - Qty 1
- Shop: Timken Bearing Kit, L44643 Inner/Outer Bearings, L44610 Inner/Outer Races, 204507 Seal
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Optronics Trailer Light Kit for Trailers over 80" Wide - Submersible - 25' Wiring Harness
- Shop: LED Trailer Combination Tail Light - Submersible - 7 Function - 10 Diodes - Red Lens - Driver Side
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Suspension Enhancement
- Q&A: Lug Nut Torque Chart for Trailer Wheels
on Trailer Spindles
Robin H.
12/15/2025
Hey Lowell, did you end up replacing the spindle or checking with Dexter about a matching axle for your trailer? Your update could make it easier for others dealing with water getting into their hubs.