Replacement Bearings and Grease Seal for 2001 Featherlite Model 4926

Question

Question:

I need a correct set of wheel bearings and seals for 2001 Featherlite Model 4926 20 car hauler w/ 3500# axles. You guys always seen to know. Thanks

asked by: Brian F

0

Expert Reply:

Thank you for providing that information. Since you know your 2001 Featherlite Model 4926 has 3,500 lb axles the correct bearing kit is the # BK2-100. This includes the # L44649 outer bearing, # L68149 inner bearing, # RG06-050 (10-19) grease seal, along with the corresponding races, cotter pin, and tang washer.

expert reply by: Robin H

0

Answer 1

Hey Craig, thanks for reaching out! I believe the Optronics Fleet LED Trailer Tail Lights w/ Grommets #TLL12RK will work as replacements for your 2008 Featherlite 4926 trailer, but you'll need to confirm this on your end. These lights carry the…

view full answer...

Answer 2

We have checked with Bulldog in the past about the replacement options for the Bulldog A-Frame Jack part 1551060301 that you have and they were able to give us all of the information we need to offer you a solution. The best option we have is the…

view full answer...

Answer 3

Hey James, you can go with a 4k axle leaf spring like the part #e22YR in place of what you have now while it has a slightly higher weight capacity it's not enough that it would create a harsh ride quality. This is a 26 inch long spring though so…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 7

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Brian, that specific mounting bracket has been discontinued but you can use the Black Molded ABS Mounting Bracket for Thin Line Series Clearance, Side Marker Lights #A65B in it's place. Let me know if there is anything else I can do for you…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Bearings and Grease Seal for 2001 Featherlite Model 4926

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching