How To Add Brakes to a Bass Tracker Boat Trailer

Question

Question:

Good afternoon I live in the mountains andI have a 2020 16 foot bass tracker aluminum trailer and it is a single axle with no brakes. Can I replace it with an axle with brakes? And if it can be done which one would you recommend? Thank you for your time.

asked by: James H

0

Expert Reply:

In most cases, you can just simply add brakes to the existing axle and you don't need an entire new axle. That said, this is all based on the axle capacity and I don't have any way to look this up for you. If you have a 3,500 lb axle for example, you'd need the following:

Electric Trailer Brake Kit part # AKEBRK-35-SA
Easy Grease Trailer Hub and Drum Assembly part # AKHD-545-35-EZ-K
Junction Box # 3375601101
7-Way Connector # H20046
Hopkins Engager Push-To-Test Trailer Breakaway Kit part # 20400

If you have a different axle capacity, just let me know what that is and I'd be glad to see if we have the parts for that.

expert reply by: Conner L

0

Scott

7/27/2024

Hi Conner, I was thinking a surge break kit for my 17.5 bass tracker would be easier, and maybe even cheaper. But I would need a actuator that fits my swing tongue. Have you had such a request? thanks, Scott

Jesse M.

7/29/2024

@Scott Yes, it is possible to add a surge actuator to a swing away tongue, and this is a request we hear fairly often. Really any actuator, such as the Demco Hydraulic Brake Actuator # DM72VR can be used on a swing away tongue as long as there is enough material on the tongue to mount it. The # DM72VR actuator will fit a 3" straight tongue. If your trailer has a different tongue size just let me know and I will see what we can offer you.

Answer 1

I recommend upgrading to the Valterra Adjustable Water Regulator #A01-1117VP. It uses a higher quality gauge and they offer a Replacement Gauge #A01-1125 in the event it is damaged. You will also be able to adjust your water pressure with this…

view full answer...

Answer 2

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 3

Thank you for the pictures! We do offer a trailer brake option that will work with the 10" wheels on your 2014 Shorelander Trailer. Since the trailer will be in water you will want to use the Dexter Hydraulic Trailer Brake Kit #23-398-399 which…

view full answer...

Answer 4

Technically yes, if you were replacing idler hubs, as long as the inner/outer bearing, grease seal AND wheel bolt pattern match, there's nothing that prevents you from using a 3,500 lb axle hub, like #84545BX on a 2,000 lb axle. If the bearings…

view full answer...

Answer 5

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 6

You will want to confirm but the Titan hubs on your boat trailer could possibly be compatible with electric brakes. You will want to inspect the inner surface. If it is flat and smooth you can use it for electric brakes. For your brakes you are going…

view full answer...

Answer 7

You can convert your trailer to electric over hydraulic brakes by using hydraulic trailer brakes, hydraulic drums, hydraulic brake lines, and adding an electric over hydraulic actuator like the HydraStar Electric Over Hydraulic Actuator for Drum…

view full answer...

Answer 8

Hi Steve; I would use 10 gauge wire #10-1-1 for the brakes instead of 12 gauge. The same butt connectors #DW05745-10 will still work. If you're connecting 3 wires together I would either use a wire nut with plenty of electrical tape or solder…

view full answer...

Answer 9

We do have a selection of fenders for 13" wheels that you can use to replace your current fenders. Among our linked selection we have different constructions like aluminum, plastic, and steel. These fenders can mount via brackets or welding…

view full answer...

Answer 10

For starters, a quick-fix type connector shown in your photo is typically a good choice for an emergency repair, but I wouldn't use it as a permanent fix. It looks like your trailer wiring has 3 separate grounds and 3 separate running lamp…

view full answer...

Answer 11

The Replacement Screen Door Latch for Right Swinging RV Entry Doors #LC27UD you were looking at could be installed in place of your current latch, but would require modification to both the screen door and door threshold to line up with the plunger.…

view full answer...

Answer 12

I wonder if the box was stressed in some way when bolting it to the trailer. Maybe one of the install bolts was pulled the box in a direction that stressed it. That said, for just the box you'd want the part #3375601101 which is an exact…

view full answer...

How To Add Brakes to a Bass Tracker Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching