Trailer Hitch For A 2007 Toyota Matrix

Question

Question:

How much does the C12013 itself weigh? Looking for a 2007 Toyota Matrix.

asked by: Michael S

1

Helpful Expert Reply:

We have the perfect trailer hitch that will fit your 2007 Toyota Matrix!

The Curt Trailer Hitch Receiver # C12013 has a shipping weight of 18 pounds. The hitch has a bolt-on installation with no welding required. It has a gloss black powder coat finish that is over a protective base coat that offers superior rust resistance.

The trailer hitch has a maximum gross trailer weight up to 2,500 pounds and has a maximum tongue weight up to 250 pounds. I would recommend checking your vehicle's manual to find out the proper towing capacity of your vehicle.

The T-One Vehicle Wiring Harness # 118386 will give you a 4-flat trailer connector that will make it to where your trailer's stop, turn, and taillights will mirror your vehicle's stop, turn, and taillights. The harness will plug into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo carrier.

You will also need The Draw-Tite Drawbar for 1-1/4 inch Hitch # 3593 and The 2 inch ball # 19258 or the 1-7/8 inch ball # 19256.

I attached a review video link below.

expert reply by: Noah E

1

Answer 1

Thanks for the picture Rich. The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter item #TRU44FR is exactly what you need if your hubs have item #L44649 inner and outer bearings. For a grease seal you'll want item #34823. We…

view full answer...

Answer 2

Curt trailer hitch #C12221 would be a good option as long as your 2005 Toyota Matrix is not an XR or XRS model. If it is an XR or XRS model then #C12013 would be the best option for a Curt hitch. These are both Class II hitches which means you have…

view full answer...

Answer 3

If you use Draw-Tite trailer hitch #24812 the center fascia (which is a fancy word for the lower plastic bumper part on your 2003 Toyota Matrix XR) will not have to be removed. I have included a link to the installation instructions for you. There is…

view full answer...

Answer 4

Yes, you are correct the differences are that on #C12221 the heat shield modification may be required, and lower fascia may need to be trimmed for hitch installation. On the #C12013 a heat shield modification may be required. It does not need a…

view full answer...

Answer 5

Hi Bernie, There is a Curt hitch for the 2003 Toyota Matrix XR, which is the Curt Trailer Hitch Receiver #C12013. This is as high as a hitch can get on your Matrix XR, and it'll be right up against that lower fascia like you had previously.

view full answer...

Answer 6

The only trimming or modification required is if your 2008 Toyota Matrix is an XR or XRS model. The installation instructions for Curt Trailer Hitch, #12221, linked below, state that if you do have an XR or XRS model, the lower valance MAY require…

view full answer...

Answer 7

Yes, the Draw-Tite Class 1 Trailer Hitch, item #24812, will fit your 2004 Toyota Matrix XRS. The rear fascia on your car has a center section that will have to be removed to install the hitch. The fascia will not be reinstalled. Some items you may…

view full answer...

Answer 8

The trailer hitch options for a 2006 Toyota Matrix XR are the Draw-Tite Sport Frame Receiver Hitch part #24812 and the Curt Trailer Hitch Receiver part #C12013 which both have a 1-1/4" receiver tube opening. I recommend the Curt Trailer Hitch…

view full answer...

Answer 9

The Curt Class-II hitch #C12221 has a higher weight rating and would work with your 2009 Toyota Matrix XRS. Draw-Tite #24812 is a Class-I hitch where as the Curt #12221 is a Class-II. The Class-II hitch will have a higher rating than Class-I. But…

view full answer...

Answer 10

The trailer hitch I recommend for your 2004 Matrix is the Curt, part #C12221. This is a Class ll hitch and it has a 1-1/4 inch receiver opening. Per Curt all non-trailer loads - bike racks, cargo carriers and so forth - should be supported with…

view full answer...

Answer 11

I went out to the warehouse and examined the Curt Hitch #12221 and #C12013. While they are similar, there is a key difference in the designs. From the top of the mounting brackets on each side of the hitch down to the bottom of the receiver, hitch…

view full answer...

Answer 12

Currently, there are 2 trailer hitches that will fit your 2005 Toyota Matrix XR. One Class-I #24812 (Draw-Tite) and one Class-II #C12013 (Curt). With that said, they are all good products but I would most certainly go with the Class-II Curt hitch…

view full answer...

Trailer Hitch For A 2007 Toyota Matrix

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching