Difference Between Trailer Hitches C12221 & C12013 On 2007 Toyota Matrix

Question

Question:

Hitch for 2007 Toyota Matrix: what is the difference between C12221 and C12013 besides cost, and it appears that fascia doesnt need mod with C12013?

asked by: Doug W

0

Expert Reply:

Yes, you are correct the differences are that on # C12221 the heat shield modification may be required, and lower fascia may need to be trimmed for hitch installation. On the # C12013 a heat shield modification may be required. It does not need a fascia modification, which presents an easier install on the 2007 Toyota Matrix.

Also the # C12013 fits the 2003 - 2008 Toyota Matrix XR and XRS.

The # C12221 fits Canadian models of the Matrix FROM 2009 - 2013 (Toyota Matrix,) and 2003 - 2010 Pontiac Vibe GT models.

If you are towing a trailer with lights the recommended harness is # 118386. The plug in location is behind the trim panels in the cargo area on the driver and passenger side. The recommended ball mount is # C45521. If you need a 2" hitch ball # A-82 is recommended. If you need 1-7/8" hitch ball # C40001 is recommended.

If you are towing a trailer with electric brakes, reply to me and I will make further recommendations.

expert reply by: Timothy G

0

Answer 1

Curt trailer hitch #C12221 would be a good option as long as your 2005 Toyota Matrix is not an XR or XRS model. If it is an XR or XRS model then #C12013 would be the best option for a Curt hitch. These are both Class II hitches which means you have…

view full answer...

Answer 2

Thanks for the picture Rich. The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter item #TRU44FR is exactly what you need if your hubs have item #L44649 inner and outer bearings. For a grease seal you'll want item #34823. We…

view full answer...

Answer 3

The instructions (see link below) state that the drawbar must be used in the rise position only, for your Pontiac Vibe. Drawbar 3593 has a rise of 2-1/8 inches, and only the drawbar recommended for a Class I hitch should be used. The manufacturer…

view full answer...

Answer 4

Currently, there are 2 trailer hitches that will fit your 2005 Toyota Matrix XR. One Class-I #24812 (Draw-Tite) and one Class-II #C12013 (Curt). With that said, they are all good products but I would most certainly go with the Class-II Curt hitch…

view full answer...

Answer 5

We have the perfect trailer hitch that will fit your 2007 Toyota Matrix! The Curt Trailer Hitch Receiver #C12013 has a shipping weight of 18 pounds. The hitch has a bolt-on installation with no welding required. It has a gloss black powder coat…

view full answer...

Answer 6

The Curt Class-II hitch #C12221 has a higher weight rating and would work with your 2009 Toyota Matrix XRS. Draw-Tite #24812 is a Class-I hitch where as the Curt #12221 is a Class-II. The Class-II hitch will have a higher rating than Class-I. But…

view full answer...

Answer 7

Hi Bernie, There is a Curt hitch for the 2003 Toyota Matrix XR, which is the Curt Trailer Hitch Receiver #C12013. This is as high as a hitch can get on your Matrix XR, and it'll be right up against that lower fascia like you had previously.

view full answer...

Answer 8

If you use Draw-Tite trailer hitch #24812 the center fascia (which is a fancy word for the lower plastic bumper part on your 2003 Toyota Matrix XR) will not have to be removed. I have included a link to the installation instructions for you. There is…

view full answer...

Answer 9

All available hitches made for your 2007 Toyota Matrix XR include both Class I and Class II types in the 1-1/4-inch size. All are shown on the linked page. You'll notice all three options, parts # 24812, #C12221 and #C12013, share a very similar…

view full answer...

Answer 10

No, you will not. Draw-Tite Class I Trailer Hitch Receiver, part #24812, is the correct hitch for your 2009 Toyota Matrix. It fits all models including those with rear fascia, and does not require cutting of the fascia. Hidden Hitch Class I Trailer…

view full answer...

Answer 11

The trailer hitch I recommend for your 2004 Matrix is the Curt, part #C12221. This is a Class ll hitch and it has a 1-1/4 inch receiver opening. Per Curt all non-trailer loads - bike racks, cargo carriers and so forth - should be supported with…

view full answer...

Answer 12

Yes, the Draw-Tite Class 1 Trailer Hitch, item #24812, will fit your 2004 Toyota Matrix XRS. The rear fascia on your car has a center section that will have to be removed to install the hitch. The fascia will not be reinstalled. Some items you may…

view full answer...

Difference Between Trailer Hitches C12221 & C12013 On 2007 Toyota Matrix

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching