Curt Trailer Hitch For 2003 Toyota Matrix XR

Question

Question:

I have a 2003 Toyota Matrix XR.. I previously had a 2005 Toyota Matrix XR I gave my brother which I had installed a hidden trailer hitch on. I would like to install a hidden hitch on my 2003 Toyota Matrix XR… The attachment point of receiver is where the ball is located is right against the bottom of the rear bumper. Nice and tight application… Could you tell me if Curt still makes that model? I have the sticker says Curt but no other numbers? Just don’t want something that isn’t as high as possible with the limited ground clearance I’m already dealing with… Open with any manufacturers? Thank you for your advice! Bernie

asked by: Bernie S

0

Expert Reply:

Hi Bernie,

There is a Curt hitch for the 2003 Toyota Matrix XR, which is the Curt Trailer Hitch Receiver # C12013.

This is as high as a hitch can get on your Matrix XR, and it'll be right up against that lower fascia like you had previously.

expert reply by: Kyle S

0

Jesse M.

1/27/2026

Hey Bernie, how did the Curt hitch work out on your 2003 Matrix XR? Did it give you that tight, high-clearance fit you were hoping for? Your feedback could help others looking for the same setup.

Answer 1

The trailer hitch options for a 2006 Toyota Matrix XR are the Draw-Tite Sport Frame Receiver Hitch part #24812 and the Curt Trailer Hitch Receiver part #C12013 which both have a 1-1/4" receiver tube opening. I recommend the Curt Trailer Hitch…

view full answer...

Answer 2

Currently, there are 2 trailer hitches that will fit your 2005 Toyota Matrix XR. One Class-I #24812 (Draw-Tite) and one Class-II #C12013 (Curt). With that said, they are all good products but I would most certainly go with the Class-II Curt hitch…

view full answer...

Answer 3

Curt trailer hitch #C12221 would be a good option as long as your 2005 Toyota Matrix is not an XR or XRS model. If it is an XR or XRS model then #C12013 would be the best option for a Curt hitch. These are both Class II hitches which means you have…

view full answer...

Answer 4

I went out to the warehouse and examined the Curt Hitch #12221 and #C12013. While they are similar, there is a key difference in the designs. From the top of the mounting brackets on each side of the hitch down to the bottom of the receiver, hitch…

view full answer...

Answer 5

All available hitches made for your 2007 Toyota Matrix XR include both Class I and Class II types in the 1-1/4-inch size. All are shown on the linked page. You'll notice all three options, parts # 24812, #C12221 and #C12013, share a very similar…

view full answer...

Answer 6

First, release the mechanism that holds the coupler onto the ball. It may be a lever or a knob that has to be turned. Some require a dual action move where you would push back or forward on the lever while lifting up on it. If you have done this and…

view full answer...

Answer 7

The Curt trailer hitch #C12013 will have the receiver just below the rear fascia on your 2006 Toyota Matrix. Take a look at the review with pictures on the product page to get an idea of where it will be. Curt does say that you need to use a…

view full answer...

Answer 8

The reason the Curt Trailer Hitch Receiver #C12228 is not listed as a confirmed fit on your 2007 Toyota Matrix XR is because it was designed to fit the 2009-2013 Matrix. For your 2007 Matrix XR you will need to use the Curt Trailer Hitch Receiver…

view full answer...

Answer 9

Thanks for the picture Rich. The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter item #TRU44FR is exactly what you need if your hubs have item #L44649 inner and outer bearings. For a grease seal you'll want item #34823. We…

view full answer...

Answer 10

Ball mounts including Curt ball mounts #C45024 and #C45014 are given their rating based on how they are tested and which applications they are made for. Other than that and the capacity they are pretty much the same.

view full answer...

Answer 11

No, you will not. Draw-Tite Class I Trailer Hitch Receiver, part #24812, is the correct hitch for your 2009 Toyota Matrix. It fits all models including those with rear fascia, and does not require cutting of the fascia. Hidden Hitch Class I Trailer…

view full answer...

Answer 12

Yes, the Draw-Tite Class 1 Trailer Hitch, item #24812, will fit your 2004 Toyota Matrix XRS. The rear fascia on your car has a center section that will have to be removed to install the hitch. The fascia will not be reinstalled. Some items you may…

view full answer...

Curt Trailer Hitch For 2003 Toyota Matrix XR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching