Availability of Class III Hitch w/ 2 Inch Receiver for 2007 Toyota Matrix

Question

Question:

Hi, Is it possible to get a 2inch hitch for a 2007 toyota matrix xr? Thanks, Erika

asked by: Erika S

0

Expert Reply:

All the hitches available for the Toyota Matrix are either Class I or II which use a 1-1/4 inch receiver tube. This being said, there's still options available that might work for you.

For the best capacity, I'd recommend the Curt Class II hitch, part # C12013 which has a 250lb tongue weight capacity and a 2500lb towing capacity. For non trailer loads like bike racks and cargo carriers, the hitch warranty stipulates that a stabilizing strap like part # 18050 should be used.

Most folks ask this question when they have a hitch accessory that's designed for a 2 inch hitch, and their vehicle doesn't have an available 2 inch hitch.

In this situation, you'd be best off replacing your hitch accessory for something that'd designed for a 1-1/4 inch hitch. There are adapters available, such as part # HTAD, but using an adapter will reduce the capacity of your hitch by 50%.

The Curt Class II Hitch I recommended would allow you to carry 4 bikes, using a bike rack like the Thule Hitching Post Pro, part # TH934XTR.

expert reply by: Mike L

0

Answer 1

Thanks for the picture Rich. The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter item #TRU44FR is exactly what you need if your hubs have item #L44649 inner and outer bearings. For a grease seal you'll want item #34823. We…

view full answer...

Answer 2

If you use Draw-Tite trailer hitch #24812 the center fascia (which is a fancy word for the lower plastic bumper part on your 2003 Toyota Matrix XR) will not have to be removed. I have included a link to the installation instructions for you. There is…

view full answer...

Answer 3

The only trimming or modification required is if your 2008 Toyota Matrix is an XR or XRS model. The installation instructions for Curt Trailer Hitch, #12221, linked below, state that if you do have an XR or XRS model, the lower valance MAY require…

view full answer...

Answer 4

I went out to the warehouse and examined the Curt Hitch #12221 and #C12013. While they are similar, there is a key difference in the designs. From the top of the mounting brackets on each side of the hitch down to the bottom of the receiver, hitch…

view full answer...

Answer 5

The trailer hitch options for a 2006 Toyota Matrix XR are the Draw-Tite Sport Frame Receiver Hitch part #24812 and the Curt Trailer Hitch Receiver part #C12013 which both have a 1-1/4" receiver tube opening. I recommend the Curt Trailer Hitch…

view full answer...

Answer 6

Curt trailer hitch #C12221 would be a good option as long as your 2005 Toyota Matrix is not an XR or XRS model. If it is an XR or XRS model then #C12013 would be the best option for a Curt hitch. These are both Class II hitches which means you have…

view full answer...

Answer 7

Yes, the Draw-Tite Class 1 Trailer Hitch, item #24812, will fit your 2004 Toyota Matrix XRS. The rear fascia on your car has a center section that will have to be removed to install the hitch. The fascia will not be reinstalled. Some items you may…

view full answer...

Answer 8

You are definitely on the right track when it comes to not wanting to use an adapter for your bike rack. The only trailer hitches that are a confirmed fit for your 2004 Toyota Matrix have 1-1/4" receivers but if you let me know what bike rack…

view full answer...

Answer 9

No, you will not. Draw-Tite Class I Trailer Hitch Receiver, part #24812, is the correct hitch for your 2009 Toyota Matrix. It fits all models including those with rear fascia, and does not require cutting of the fascia. Hidden Hitch Class I Trailer…

view full answer...

Answer 10

The instructions (see link below) state that the drawbar must be used in the rise position only, for your Pontiac Vibe. Drawbar 3593 has a rise of 2-1/8 inches, and only the drawbar recommended for a Class I hitch should be used. The manufacturer…

view full answer...

Answer 11

Hi Bernie, There is a Curt hitch for the 2003 Toyota Matrix XR, which is the Curt Trailer Hitch Receiver #C12013. This is as high as a hitch can get on your Matrix XR, and it'll be right up against that lower fascia like you had previously.

view full answer...

Answer 12

The Curt Class-II hitch #C12221 has a higher weight rating and would work with your 2009 Toyota Matrix XRS. Draw-Tite #24812 is a Class-I hitch where as the Curt #12221 is a Class-II. The Class-II hitch will have a higher rating than Class-I. But…

view full answer...

Availability of Class III Hitch w/ 2 Inch Receiver for 2007 Toyota Matrix

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching