Trailer is not Level When Towing with Recommended Drawbar

Question

Question:

I purchased this hitch and the recommended drawbar but my trailer is not level when towing. Front is lower, is there anthing I can do to get my trailer level?

asked by: Jerry F

0

Expert Reply:

The instructions (see link below) state that the drawbar must be used in the rise position only, for your Pontiac Vibe. Drawbar 3593 has a rise of 2-1/8 inches, and only the drawbar recommended for a Class I hitch should be used. The manufacturer tests for crash safety on Class I and Class II hitches and their recommendation should be followed. If your drawbar is in the correct position and the trailer is still not level you may need to haul that particular trailer with another vehicle.

I have posted a link on how to measure for correct towing height and ball mount selection.

expert reply by: Robert G

0

Answer 1

Thanks for the picture Rich. The BTR E-Z Lube Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter item #TRU44FR is exactly what you need if your hubs have item #L44649 inner and outer bearings. For a grease seal you'll want item #34823. We…

view full answer...

Answer 2

No, you will not. Draw-Tite Class I Trailer Hitch Receiver, part #24812, is the correct hitch for your 2009 Toyota Matrix. It fits all models including those with rear fascia, and does not require cutting of the fascia. Hidden Hitch Class I Trailer…

view full answer...

Answer 3

All the hitches available for the Toyota Matrix are either Class I or II which use a 1-1/4 inch receiver tube. This being said, there's still options available that might work for you. For the best capacity, I'd recommend the Curt Class II…

view full answer...

Answer 4

I spoke with my contact at Curt and the measurement from where the hitch mounts to the frame down to the top of the receiver is 6.69 inches on Curt trailer hitch #C12013. From the top of the receiver to the bottom is 1-3/4 inches. I have included a…

view full answer...

Answer 5

Hi Bernie, There is a Curt hitch for the 2003 Toyota Matrix XR, which is the Curt Trailer Hitch Receiver #C12013. This is as high as a hitch can get on your Matrix XR, and it'll be right up against that lower fascia like you had previously.

view full answer...

Answer 6

The Curt Class-II hitch #C12221 has a higher weight rating and would work with your 2009 Toyota Matrix XRS. Draw-Tite #24812 is a Class-I hitch where as the Curt #12221 is a Class-II. The Class-II hitch will have a higher rating than Class-I. But…

view full answer...

Answer 7

Curt trailer hitch #C12221 would be a good option as long as your 2005 Toyota Matrix is not an XR or XRS model. If it is an XR or XRS model then #C12013 would be the best option for a Curt hitch. These are both Class II hitches which means you have…

view full answer...

Answer 8

We have the perfect trailer hitch that will fit your 2007 Toyota Matrix! The Curt Trailer Hitch Receiver #C12013 has a shipping weight of 18 pounds. The hitch has a bolt-on installation with no welding required. It has a gloss black powder coat…

view full answer...

Answer 9

The only trimming or modification required is if your 2008 Toyota Matrix is an XR or XRS model. The installation instructions for Curt Trailer Hitch, #12221, linked below, state that if you do have an XR or XRS model, the lower valance MAY require…

view full answer...

Answer 10

I went out to the warehouse and examined the Curt Hitch #12221 and #C12013. While they are similar, there is a key difference in the designs. From the top of the mounting brackets on each side of the hitch down to the bottom of the receiver, hitch…

view full answer...

Answer 11

Yes, the Draw-Tite Class 1 Trailer Hitch, item #24812, will fit your 2004 Toyota Matrix XRS. The rear fascia on your car has a center section that will have to be removed to install the hitch. The fascia will not be reinstalled. Some items you may…

view full answer...

Answer 12

All available hitches made for your 2007 Toyota Matrix XR include both Class I and Class II types in the 1-1/4-inch size. All are shown on the linked page. You'll notice all three options, parts # 24812, #C12221 and #C12013, share a very similar…

view full answer...

Trailer is not Level When Towing with Recommended Drawbar

Featured Help Information

Miscellaneous Media

Continue Researching