Replacement End Fitting For Lippert Hydraulic Slide Out

Question

Question:

Does this my hydraulic slide out system Lippert unit #19995

asked by: Marlin L

0

Expert Reply:

Yes, the Lippert Replacement End Fitting for Hydraulic Hose on RV Leveling Systems # LC249363 has a inside hose dimeter of 1/4" and a 1/4" female SAE ORFS port which is standard on Lippert Hydraulic and motorized leveling systems.

expert reply by: Bryce D

0

Answer 1

Hello Sean, I do not have a database that shows exactly what components are installed on each individual trailer, but based on my research, you should have a tandem axle setup with each axle rated at 4,400 pounds. You can check the axle tag to…

view full answer...

Answer 2

Hello Doug, Great question, and I am happy to make sure we get you into the right leaf spring. Since there is not a real standard for putting trailers together I am going to need a measurement from you. I need you to measure the Leaf Spring as…

view full answer...

Answer 3

The 125340 motor that you currently have on your 2008 Montana Mountaineer 35 foot 5th Wheel is equivalent to the Replacement Motor #LG-142178. This is compatible with the Replacement Aluminum Gearbox #LG-179015 which is also what you want to use for…

view full answer...

Answer 4

We do not currently offer the specific hydraulic hoses that Lippert's leveling systems come with but we do offer the JIC #LC138416 and ORFS #LC249363 fittings so that you can just get whatever length hydraulic hose you need and then crimp on the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement End Fitting For Lippert Hydraulic Slide Out

Product Page this Question was Asked From

Continue Researching