Light Duty Brophy Cable Camper Jack Options

Question

Question:

do you have a light duty version of this Item # CJ74 , I need the height but my shell is less than 200lbs

asked by: Ron M

0

Expert Reply:

If you're needing the 67" max lift then you can get two of the 1,500 lb version # CJ74H. Same Max Lift just half the weight capacity. If you do not really need up to 67 inches of lift, you can get the # CJ31 that will have a Max Lift of 57 inches and a capacity of 1,000 lbs. These are both great options that are more light duty than the 3,000 lb jacks # CJ74.

I've included some videos for you to check out if you wanted to learn more!

expert reply by: Adam E

0

Answer 1

I checked with Brophy and the Brophy Camper Jacks #CJ31 have a distance of 3 inches from the upright mast to backside of the bracket that would hold your camper shell.

view full answer...

Answer 2

As long as the bed rails on your truck are not more than 57" from the ground then you could certainly use the Brophy Cable Camper Jacks part #CJ31 to lift the camper shell up from your truck bed. Once lifted, you could just simply drive away and…

view full answer...

Answer 3

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...

Answer 4

You should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back.…

view full answer...

Answer 5

Thanks for the kind words! Yes, the Custom Fit Tie Down Kit item #TL82FV does include both Front item #TLF2018 and Rear item #TLF3007 tie downs. These fit the 2018 Ford F-150 with a 6-1/2' bed.

view full answer...

Answer 6

You should be able to change the orientation of the Brophy Cable Camper Jacks #CJ74 so that the legs pointing towards the cab of your pickup and the other legs will sit under your pickup bed a little to help stabilize your camper. I have attached a…

view full answer...

Answer 7

The Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger - 35 Amp item #PD4135K is the replacement for the Magnetek 6300 Q series RV converter. It comes with the front cover. The AC breakers and DC fuse…

view full answer...

Answer 8

The Brophy Cable Camper Jacks - 67" Max Lift Height - 3,000 lbs - Qty 2 #CJ74 is the same jack as the #CJ74H only sold as a pair. There are no specs that are different between the two parts outside of the quantity.

view full answer...

Answer 9

I measured the inside diameter of the Replacement Tripod Base for Brophy Cable Camper Jacks #1106 and found it was 2 inches. This base is a replacement for the Brophy Cable Camper Jacks - 57" Max Lift Height #CJ41 and 67" Max Lift Height…

view full answer...

Answer 10

The connector for the Tekonsha Plug-In Wiring Adapter #3070-P is located above the parking brake on your 2023 Honda Ridgeline. Even knowing where it is still proves difficult to get to the connector and attach the wiring adapter. I know several…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

For a 2023 GMC Canyon we currently offer the BedRug Custom Full Truck Bed Liner #BR76ZR, which will fully cover the bed, bedrails, bulkhead, and tailgate. It's made of a 3/4" thick layer of polypropylene to cushion valuable loads and help…

view full answer...

Light Duty Brophy Cable Camper Jack Options

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching