Fit of D Washer and Tang Washer for 1-1/16 Inch Spindle

Question

Question:

I saw a Tryryde tang type spindle washer part # 5-101. The inner diameter is 1 inch. My bearings are 1 and 1/16 inch. Does this part come in that size?

asked by: James S

0

Expert Reply:

The washer # 5-101 is the 1 inch diameter standard size and there is not anything that is 1-1/16 inches as you stated. This washer will work well along with the D Washer for EZ Lube Spindles # 5-23 for your spindle and bearings.

expert reply by: Jason S

0

Answer 1

Hello Darin, Based on the information you provided, it sounds like your trailer is using one of the older shorter-style hubs that were commonly found on some EZ Loader boat trailers. Unfortunately, we no longer carry that shorter hub design, and the…

view full answer...

Answer 2

While your spindle may have a diameter of 1-1/16 inch where the bearings ride the diameter where the threads are is actually 1 inch like what the part #5-23 that you referenced assuming you have a standard trailer spindle which it sounds like you…

view full answer...

Answer 3

A 3,000 lb axle is an odd size but I was able to find what you need. There isn't a kit, but you can get the bearings which are available individually. You will need bearing #LM67048 and bearing #L44649 for each hub. You will also need grease seal…

view full answer...

Answer 4

On Dexter axles manufactured after April 2001 you will be able to find the serial number stamped on the rear portion of the axle tube approximately 18" from the passenger side hub. Depending on the condition of the axle you may need some chalk…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Fit of D Washer and Tang Washer for 1-1/16 Inch Spindle

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching