Does Trailer with 1-1/16 inch Spindle Need 1-1/16 inch Diameter Washer

Question

Question:

Hello: I cannot find 1 1/16inch spindle washers D-washer but any would work. Put new 1 1/16inch bearings on to trailer spindle, cannot find the 1 1/16inch washers? Thanks for any guidance

asked by: JD H

0

Expert Reply:

While your spindle may have a diameter of 1-1/16 inch where the bearings ride the diameter where the threads are is actually 1 inch like what the part # 5-23 that you referenced assuming you have a standard trailer spindle which it sounds like you do.

expert reply by: Jameson C

0

Answer 1

To install the Prodigy P3 Trailer Brake Controller #90195 in your 2019 Nissan Pathfinder you can find the brake controller port directly under the dash as in the accompanying photo. This will allow you to plug in the Tekonsha Plug-In Wiring Adapter…

view full answer...

Answer 2

Yes, there should be a washer of some type between the spindle nut and the bearing on your trailer. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. There are several types of spindle…

view full answer...

Answer 3

The slight gap you see is normal. The drum is not supposed to make contact with the brake mounting plate. There are some instances when mixing brands of brakes, hubs, and axles, that won't line up properly but in this case it is normal. I did…

view full answer...

Answer 4

Aluminum trailer frames or bodies can cause grounding issues so I suggest using a separate ground wire that runs from the rear of the trailer up to the main ground post in the junction box like #38656. You can join the ground wires for the individual…

view full answer...

Answer 5

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 6

I went out to our warehouse to take a couple of measurements on the CE Smith Double U-Bolt Bolster Bracket #CE10190GA referenced in your question. From outer edge to outer edge on the parallel slots, there is a distance of 2-1/4 inches. From the top…

view full answer...

Answer 7

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 8

It actually sounds like the hub that is sitting flush isn't pushed on all the way. The area the seal sits should stop the bearing from moving too far, so I suggest pushing that one on further and they should then match each other.

view full answer...

Answer 9

The closest grease seals that we carry to the dimensions you have specified are Grease Seals, #RG06-020, for a double lip seal pair, or #10-9 for 1 seal. These have an inner diameter of 1.5 inches and an outer diameter of 1.987 inches. That is only…

view full answer...

Answer 10

Whatever bearing kit you got likely came with both to give you options. Since you already had a tang washer on your spindle you can stick with the tang washer. Using the tang washer like the #5-101 with a D washer like the #5-23 would give you no…

view full answer...

Answer 11

The correct way to wire your breakaway battery, like the Hopkins Engager #20400, is to have the black wire from the battery connected to the 12V power on your trailer, and then the blue wire to your breakaway switch which, in turn, connects to the…

view full answer...

Answer 12

To be on the safe size, I recommend going with a 13 inch bracket #CE10002G-4 at the back of the trailer and an 11 inch bracket with #CE10003G at the front. A nice feature on these brackets is that they will each actually have as much as 3-3/4 inches…

view full answer...

Does Trailer with 1-1/16 inch Spindle Need 1-1/16 inch Diameter Washer

Product Page this Question was Asked From

Continue Researching