Locking Hitch Pin Recommendation for Yakima DoubleDown Bike Rack

Question

Question:

Will this fit a Yakima Doubledown 2 with thread 1/2 - 13 pitch?

asked by: Tim

0

Expert Reply:

If you had the version of the Yakima DoubleDown that used a threaded hitch pin the lock kit you'd want is the # Y07235 which would use the hitch pin the rack already has. If you wanted an option to lock the rack as well as bikes to the rack you'd want the part # Y07238.

expert reply by: Jameson C

0

Answer 1

For your 2018 Ford Edge (Sport or non-Sport) the best hitch based on what you want is the Draw Tite part #75234. This hitch has a concealed crosstube which means only the hitch opening would hang down below the rear bumper. Check out the picture I…

view full answer...

Answer 2

The best choice for a trailer hitch for carrying a bike rack with your 2018 Ford Edge SE is the Draw Tite part #75234 as it has the 2 inch hitch size you want, has plenty of weight capacity, and also is only option with a concealed crosstube which…

view full answer...

Answer 3

Hi Victor; like many other bike racks the Yakima DoubleDown uses a uniquely threaded hitch pin so you will need to stick with the Yakima replacement. The hitch pin is the #Y8890176 and then for the lock you can use the #Y07235.

view full answer...

Answer 4

Hello Hal, Great question! It really would be nice if Toyota kept their receiver the same size as everyone else’s so any standard 2" lock would fit. The good news is that Infinite Rule actually made a lock specifically for the 2024+ Toyota…

view full answer...

Answer 5

Yes, you can replace the hitch lock housing on your Yakima DeadLock. The part you are looking for is the Yakima Replacement Hitch Lock Housing, #Y8820048. You will also need to purchase a replacement lock core to match your existing A133 keys,…

view full answer...

Answer 6

The #Y8890200 hitch pin will fit the Yakima KingPin, but it still won't be long enough to pass through your wider that usual factory receiver on your Toyota Tacoma. You'll need to remove the threaded insert in the shank of your bike rack, and…

view full answer...

Answer 7

Thanks for the pictures John! I reached out to Yakima and they are aware of the double wall receiver on the new Toyota's but do not have a solution for it as of (09/12/2024). The only solution I have for you today is to drill out the threads on…

view full answer...

Answer 8

I believe you are referring to the Yakima HoldUp #Y02443. If you need just the HitchLock alone, that is the #Y07235. However, if you need the hitch pin that is compatible with both the HitchLock and the HoldUp itself, that is the #Y8890200.

view full answer...

Answer 9

We have actually seen this issue before. The 2" receivers on Toyota trucks and SUVs have a slightly larger diameter on the outside of the receiver tube than most typical 2 inch hitches. This is partially the powder coating, but the steel itself…

view full answer...

Answer 10

Hey Eric, I spoke with Yakima and they unfortunately no longer offer a compatible hitch pin for the HookUp bike rack. Back when this was available there weren't double-walled trailer hitch receiver tubes so the pin length wasn't an issue. The…

view full answer...

Answer 11

The Yakima HitchLock for Yakima Hitch Mounted Bike Racks - Same Key System (SKS) #Y07235 is the lock you are seeking. It is designed to work with the Replacement Hitch Bolt, Nut and Clip for Yakima Bike Racks and DryDock Load Assist - 2" Hitches…

view full answer...

Answer 12

I contacted our representative at Yakima regarding a shorter replacement bolt for the Yakima DoubleDown #Y0424. The replacement bolt part 8820052 was 3-3/4 inches long but is now discontinued. Discontinued part 8820052 has been replaced by Yakima…

view full answer...

Locking Hitch Pin Recommendation for Yakima DoubleDown Bike Rack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching