Hello Desiree, thanks for reaching out. We have just the thing! For your 2023 Chevy 2500 High Country Diesel I recommend the following: - Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F64XV This…
Hey Dave, thanks for the pictures! Based on what you have and what you are looking for the Tie Down Spare Tire Mount part #TD66FR that you referenced would be a great option. This is very similar to what you have now so it would do a great job.
The only bolt-on swivel jack we have that works with 6" tall trailer frames is the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211. The Trailer Valet has a 500 lb tongue weight capacity and works with frame rails up to 2-3/4"…
Hey Phil! For a tandem axle trailer you will want two of the Leveling Kit with Wheel Chocks for Trailers and RVs #WS28ER. You are correct, one under each tire is best. I use these on my Jayco with one under each tire to keep them off the ground and…
First we need to find out if the problem is your tow vehicle wiring or your trailer wiring. To do this use a circuit tester like part #PTW2993 to test all of the pins on your 7-way for the correct function compared to the diagram I attached. Next use…
Hey Derek, thanks for the picture! The SeaSucker Universal Recovery Board Mount - Vacuum Mount item #SEA39XR is going to work great on your setup. These will have no problem attaching to the aluminum sides. It's not going to delaminate the…
You'll need to remove the ring terminal screws that hold the white wires of the #8880162 to the trailer but then the other connections simply plug into the female matching end on the trailer since it uses bullet connectors.
The Buyers Products 24" Fluorescent Orange Marker Kit #3371308103 are a hollow Nylon construction. They are pretty rigid/sturdy and are designed to be used on vehicles.
You could for sure. You would however want to make sure that the fender is reinforced enough to support the Markers #3371308103 so that they don't just rip the metal or plastic of the fender. I'd get some flat metal from a local home…
Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…
You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…
Hello Desiree, thanks for reaching out. We have just the thing! For your 2023 Chevy 2500 High Country Diesel I recommend the following: - Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F64XV This…
Hey Dave, thanks for the pictures! Based on what you have and what you are looking for the Tie Down Spare Tire Mount part #TD66FR that you referenced would be a great option. This is very similar to what you have now so it would do a great job.
The only bolt-on swivel jack we have that works with 6" tall trailer frames is the Trailer Valet 5X Swivel Jack and Trailer Mover part #STC-V211. The Trailer Valet has a 500 lb tongue weight capacity and works with frame rails up to 2-3/4"…
Hey Phil! For a tandem axle trailer you will want two of the Leveling Kit with Wheel Chocks for Trailers and RVs #WS28ER. You are correct, one under each tire is best. I use these on my Jayco with one under each tire to keep them off the ground and…
First we need to find out if the problem is your tow vehicle wiring or your trailer wiring. To do this use a circuit tester like part #PTW2993 to test all of the pins on your 7-way for the correct function compared to the diagram I attached. Next use…
Hey Derek, thanks for the picture! The SeaSucker Universal Recovery Board Mount - Vacuum Mount item #SEA39XR is going to work great on your setup. These will have no problem attaching to the aluminum sides. It's not going to delaminate the…
You'll need to remove the ring terminal screws that hold the white wires of the #8880162 to the trailer but then the other connections simply plug into the female matching end on the trailer since it uses bullet connectors.
The Buyers Products 24" Fluorescent Orange Marker Kit #3371308103 are a hollow Nylon construction. They are pretty rigid/sturdy and are designed to be used on vehicles.
You could for sure. You would however want to make sure that the fender is reinforced enough to support the Markers #3371308103 so that they don't just rip the metal or plastic of the fender. I'd get some flat metal from a local home…
Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…
You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…
Traction Boards with 2 Boards for snow, ice, and mud
Pack 2 boards to get moving when tires spin on snow, ice, or mud. This pair fits under a pair of wheels for quick recovery, stores compactly, and can double as a shovel to set them in place. You'll find mounting options for platform racks and t-slot crossbars with hardware that accepts locks, and some setups can be drilled to ladder-rack uprights if you want them ready on the rig.
They're for recovery, not leveling. If a design folds, the hinges are meant to collapse for storage and aren't set up for weight as levelers. For keeping a camper from sinking in sand, use larger jack footplates or proper leveling gear instead.
Use mounts that fit into t-slots on crossbars or platform racks, or secure to uprights with compatible hardware. Look for pin or strap systems and add locks where the pins provide holes for them. If your rack lacks accessory slots, drilling the uprights for a mount can work—confirm your rack allows this.
Yes, 2 Boards can get you out. Dig to clear space, slide them under the drive wheels, and work the vehicle back and forth. If you're high centered or a wheel slips off, reset and try again. Adding 2 more can simplify tough recoveries by giving all 4 wheels grip as suspension moves.
Yes, 2 Boards under the drive wheels can provide the grip needed to move on ice. Place them under the front wheels for a front-drive situation or where traction is lacking. If the rear is light when unloaded, focus on the wheels that spin. Some also use boards to raise a vehicle a few inches for maintenance tasks.
Traction Boards Parts or Accessories
Filters
