A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson
(67 reviews)
Price: $103.07
In Stock
A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson
Item # DL22530
Our Price: $103.07
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (67)
- Q & A (0)
- Photos
Dutton-Lainson Trailer Jack - DL22530
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Utility Trailer
- 0 - 1000 lbs
- Sidewind Jack
- Bolt-On
- Weld-On
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- 15 Inch Lift
- No Wheel or Foot
- Steel
- Dutton-Lainson
1,000 lb Sidewind A-frame Jack
Features:
- 1,000 lb. A-frame jack
- 15" Travel
- 29-3/4" Maximum tongue height
- 15-1/4" From bracket to the top of the jack
- Inner tubing diameter: 1-3/4"
- Outer tubing diameter: 2"
- Can be welded or bolted to standard A-frame couplers
- Zinc plated TUFFPLATE finish for a longer life
- Zinc plated yellow chromate TUFFPLATE finish has three times the corrosion resistance of standard zinc plated trivalent chrome process and 30 percent greater corrosion resistance when compared to powder coated finish. Results of lab test using 5 percent neutral salt spray confirms our TUFFPLATE finish provides in excess of 500 hours against First Red Rust and in excess of 100 hours of First White Corrosion.
- Removable foot sold separately
- 3-Year limited warranty
- Made in the USA
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
22530 1,000 lb A-frame Trailer Jack by Dutton-Lainson Model 6418
Customer Satisfaction Score:
90% were satisfied with this product
10% of customers were not satisfied
- Wrong item was ordered
- Alternate product found
- Did not fit
Customer Reviews
A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson - DL22530
Average Customer Rating: 4.9 out of 5 stars (67 Customer Reviews)
1,000 lb Sidewind A-frame Jackby: Paul09/03/2023
The Jack was easy to install and etrailer was the only place I could find the right one to fit my very old (1999) tent trailer.
by: Bill 06/21/2023
This was a good replacement for the original on our vintage camper. Pretty simple - just used a grinder to remove the welded on old one, and bolts to attach the new.
by: Lorin05/31/2023
Unfortunately my initial search for a replacement for the Atwood Model 80274 suggested the Pro Series 2000 LB jack. But trying to install that jack I found it was too big. However talking directly to customer service they were able to direct me to thing model jack which was a direct replacement that I needed. They took back the wrong jack with no problems.
by: Moose05/07/2020
Most 1000 lb jacks are too wide for older camper trailers like mine. This was the only option i could find with a diameter of 2 inches! Took some elbow greasr, but once it went in the rest was easy and the included hardware worked very well. I would recommend adding 3-6 washers as they're not included and make a difference. It cranks clean and smooth! Great product so far. Customer service was very active and helpful in making sure I got what I needed and there were no issues. Odelia was very helpful! Thank you etrailer!
by: David05/03/2020
Once I modified my camper tongue, the jack fit and operated flawlessly.
by: William H.07/11/2016
The trailer jack was easy to install and works great. The removable foot is very convenient.
by: Jason 06/29/2022
Excellent product the quality was better than the original jack on the camper from the manufacturer
by: Ed09/16/2016
*Although I have not installed the trailer jack yet it looks like a direct replacement for the original one on my boat trailer. The wheel that goes with the jack definitely looks like a better fit than original.
*The electrical 4 conductor plug set... I'm using for a quick disconnect for a third
( center ) brake light for tailgaters
by: Woodjunky09/10/2017
Once again, etrailer impresses me. Ordered my jack stand on Friday and it arrived on Saturday. What great service!
Woodjunky
9/10/2018
I love the products and the value. The lights and jack are hard at work on my boat trailer. Thanks for the follow up.
by: Mark 11/18/2020
This trailer Jack has all the capacity and lift height I need. It cranks easy, has a nice finish and in my opinion, of good quality.
by: Bill 12/27/2022
Works well
by: Jon 04/23/2021
Great product wish they had the option of coming without the triangle mounting. I will have to remove this but so happy to find this size for my vintage trailer!
by: MARVIN03/21/2014
PURCHASED NEW COUPLER, JACK, AND FOOT.
ALL WERE OF GOOD QUALITY, THE COUPLER, INSTALLED, QUITE EASILY, (REPLACEMENT FOR WORN OUT COUPLER)
THE JACK AND FOOT PA WORK VERY WELL.
HIGHLY RECOMMENDED
by: Brad 11/29/2021
Looks like a good jack that will fit the smaller outer tube dimension for a vintage trailer.
by: Jeff12/07/2017
Perfect replacement. took about as long to install as it did to open the box. Great product.
by: Kenneth a03/03/2018
Nice trailer jack. Fit perfect in place of my broken one.
by: Mr. Larry 07/06/2019
Fit, value, product performance and customer service top notch !!!
Mr. L.
7/7/2020
Went on perfect and still working like a champ !!!
by: John03/13/2020
Although I haven't had a chance to install my new products yet I have to tell you how happy I was to recieve my shipment so quickly. Well done etrailer!
by: John09/15/2015
George, ordered it and it was here in 3 days, great service!
Thanks,
by: Louis11/15/2023
Fit great
by: Mehgan07/06/2023
by: Danny N.07/12/2013
Product was exactly as described!
It fit correctly and works good!
by: Richard 06/04/2023
by: Thomas 07/01/2021
25
67
Show More Reviews
See what our Experts say about this Dutton-Lainson Trailer Jack
- What Are the Dimensions and Hole Size of Mounting Flange on Dutton-Lainson Trailer Jack, # DL22530,I went out to our warehouse and measured the Dutton-Lainson Trailer Jack, # DL22530, the mounting flange hole size is 7/16 inches x 3/4 inches and the dimensions from center of one hole to the center of the next hole is 3 inches. They are equally spaced apart.
view full answer... - Which Way Will the Handle Face on the Dutton-Lainson A-Frame Trailer Jack # DL22530The orientation of the handle on the A-frame trailer jack # DL22530 will depend on the hole pattern on the trailer. The jack uses a 3 hole pattern that is basically in the shape of a triangle. The handle will be in a different place depending on how you want to mount it. Normally, the handle would be off to the left side of the trailer.
view full answer... - Trailer Jack with Outer Tube Diameter Closest to 1.9 inch.1.9 inch is going to be a bit too small. Would 2 inch work? That's the closest we have like the Dutton Lainson part # DL22530 that you referenced. Maybe you could enlarge the hole with a dremel type grinder.
view full answer... - What is the Angle of the Handle on the A-Frame Trailer Jack DL22530In regards to the A-Frame Trailer Jack part # DL22530, the handle sits at a 90 degree angle in relation to the rear two mounting holes. The distance between the inside of the handle and the outer tube of the jack is 1-1/8". I have filled these figures in for you using the photo you sent.
view full answer...
- 2 inch Outer Diameter A-Frame Trailer Jack RecommendationI have good news, our trailer jack that has a 2 inch outer diameter part # DL22530 would fit and work well. While it has a 1,000 lb weight capacity that does not mean 1,000 lb total trailer weight capacity. That capacity is the tongue weight capacity which is normally 10-15 percent of the total trailer weight. So your trailer would be looking at around 150 lbs of tongue weight which would be no problem for this at all.
view full answer... - Replacement 2" Diameter A-Frame Jack for Jayco Eagle Trailer I have a great option to replace to replace a 2" diameter Atwood a-frame trailer jack. For this, I recommend the A-Frame Trailer Jack part # DL22530. Unfortunately, side wind is the only option for these smaller diameter a-frame jacks.
view full answer... - A-Frame Jack Recommendation for Jayco Trailer that Needs 2 inch Outer Tube DiameterThe diameter of the outer tube of the Jack part # DL22530 that you referenced is 2 inches. the diameter of the inner tube is 1-3/4 inches. Most jacks have a slightly larger outer tube at 2-1/4 inches. I attached an install video for this jack for you to check out as well.
view full answer... - A-Frame Trailer Jack with an Outer Tube Diameter of 2 InchesAn A-frame trailer jack that fits your 2 inch outer tube diameter is the Dutton-Lainson # DL22530. It provides 15 inches of lift and has a 1,000 pound capacity. When fully retracted you'll have about 8-3/4 inches of clearance. Of the 2 inch diameter jacks we carry this is the least amount of clearance available.
view full answer... - Retracted and Extended Height of Dutton Lainson Trailer Jack DL22530The retracted height of the Dutton Lainson Trailer Jack # DL22530 is 8-1/4 inches and the extended height is 23-1/4 inch. From the mounting bracket to the top of the jack measures 15-1/4 inches.
view full answer... - Will Removable Wheel for Dutton-Lainson A-Frame Trailer Jack # DL22414 Fit Jack w/ 1-3/4The Removable Wheel, # DL22414, was designed to be used with the Dutton-Lainson 1,000 lb A-Frame Trailer Jack, # DL22530, which has an inner tube / down tube diameter of 1-3/4 inches so this may work for you. This wheel is intended to be held on to the jack tube with a snapper pin. Please keep in mind that Dutton-Lainson designed their accessories to be used with their jacks. Since this wheel has not been tested with other brands of trailer jacks, we can not guaranty it's compatibility.
view full answer... - Availability of 1000-lb-Rated Dutton Lainson A-Frame Tongue JackWe do carry trailer tongue jacks including products from Dutton Lainson. We offer the 1000-lb-rated side-wind tongue jack # DL22530 which comes without a wheel or foot and that can be installed either by welding or by bolting it to your trailer tongue. This jack provides 15-inches of lift height. All 1000-lb-rated a-frame tongue jacks are displayed on the linked page. I searched the Dutton Lainson website for your original part number and it no longer returns any results so it is likely...
view full answer... - Functionality of Dutton-Lainson Removable Wheel Part DL22414The Dutton-Lainson removable wheel for A-frame jack # DL22414 does swivel. It is compatible with Dutton-Lainson model 6418 trailer jack # DL22530. The wheel does not have bearings between the hub and sleeve. It will have a quick-attach pin for easy installation and removal. The wheel will make it easy to maneuver the trailer into the hitching position. It's recommended that the wheel is removed before travel. I have included FAQ and a couple video reviews for you as well.
view full answer... - Are Rubber Wheels Available for Dutton-Lainson A-Frame Trailer JackThe Removable Wheel for Dutton-Lainson A-Frame Trailer Jack Model 6418 # DL22414, which fits Dutton-Lainson Jack # DL22530 does not have a rubber wheel available. I looked through each of our jack wheels with casters as well as the wheels by themselves and there are no rubber wheels for these jacks.
view full answer... - What Is The Collar Inside Measurement Of The DL22414 Trailer jack Wheel?The Removable Wheel for Dutton-Lainson A-Frame Trailer Jack Model 6418 # DL22414 is compatible with the A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson # DL22530 which has an outer diameter tube 2 inches and the inner diameter at 1-3/4 inches. This wheel fits inside that tube, so the diameter is 2 inches on the outside and 1-3/4 inches on the inside. I went out to our warehouse to measure it and confirm.
view full answer... - A-Frame Trailer Jack With 2 Inch Outer Tube for Lightweight TrailerThere is one A-frame jack that has an outer tube that is 2 inches in diameter that is for a lightweight trailer, the A-Frame Trailer Jack # DL22530. This jack has a 1,000 lb capacity which is plenty for you (and the lightest available) and for a foot you will need to add the Removable Steel Foot # DL22541.
view full answer...
- Recommended A Frame Trailer Jack For A 1964 Airstream SafariThat is a very cool camper! We do have a jack that will fit your description. I recommend the Dutton-Lainson A-frame jack # DL22530. The outer tube has a diameter of 2" and the inner tube is a 1-3/4" diameter. It bolts on using the standard triangular 3 hole mount. The jack itself is rated for 1,000 lbs which should be more than enough for your '64 Airstream Safari.
view full answer... - Dimension of the Outer Tube On the 1,000 lb A-frame Trailer Jack by Dutton-LainsonThe Tube that goes through the trailer frame and that the mounting flange is attached to is 2 inches diameter. The inner tube that extends downward to raise the trailer is 1-3/4 inches diameter.
view full answer... - Replacement A-Frame Sidewind Jack with 2 Inch Diameter Outer TubeWe have one sidewind A-frame jack with a 2 inch outer diameter tube, part # DL22530. This is a 1,000 pound jack from Dutton-Lainson that has 15 inches of travel. I've linked a video of the jack for you as well.
view full answer... - Foot Plate Recommendation for a Jack with a Tube Outside Diameter of 1-3/4 inchesThe Removable Steel Foot with Pin # DL22541 is designed to fit a jack tube with an outside diameter of 1-3/4 inches. The jack it is designed to fit is the part # DL22530. Without knowing what brand jack you have it would be hard for me to say for certain if this footplate would work for you but it would be the best option we have.
view full answer... - Wheel Caster for Dutton Lainson Trailer Jack DL22530For the Dutton Lainson trailer jack part # DL22530 that you referenced we have the replacement wheel part # DL22414.
view full answer... - Recommended A-Frame Jack With Close To A 1-7/8 Inch DiameterFor an A-frame jack that meets that diameter criteria, I recommend the A-Frame Trailer Jack by Dutton-Lainson # DL22530 . This jack will have an inner tube diameter of 1- 3/4 inches and an outer diameter of 2 inches. It is constructed of heavy duty steel and has a zinc plated finish to resist corrosion. With this jack, I recommend the foot plate # DL22541 or the wheel # DL22414. These inner and outer dimensions are as close as we come to the 1-7/8 inch diameter.
view full answer... - Replacement Parts for Dutton Lainson Trailer JackWe do offer both replacement parts and complete Dutton Lainson trailer jacks. All complete jacks can be view by clicking on the linked page. All Dutton Lainson jack replacement parts can be viewed by clicking on the other featured link. You can use the filters on the pages to select your type of jack and the type of replacement part you need, such as caster wheel # DL22414 that fits their a-frame jack # DL22530. I checked with Dutton Lainson for your part number 203960B but this was not...
view full answer... - Recommended Foot with Pin for a 1000 lb Trailer Jack A 1,000 lb jack like the A-Frame Trailer Jack - by Dutton-Lainson # DL22530 has a smaller diameter like you stated. This jack has a diameter of 1-3/4 inches for the inner tube. For this jack you would want the Removable Steel Foot with Pin for DL22530 A-Frame Trailer Jack by Dutton-Lainson # DL22541 or wheel # DL22414.
view full answer... - Recommended A-Frame Trailer Jack for Tongue Weight of Less Than 500 lbsAn A-Frame Trailer Jack only needs to have the capacity to lift the tongue weight since it is positioned on the trailer tongue. For a trailer with a dry tongue weight of under 500 lbs I recommend the Dutton-Lainson A-Frame Jack # DL22530; you could then add a foot plate with # DL22541 or wheel with # DL22414 depending on what you need. I've added links to video reviews of these products for you to take a look at as well.
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
Adam R
Updated by:
Adele M
Updated by:
Wilson B
Updated by:
Mike S
Video Edited:
Dustin K
Installed by:
Cole B
Video by:
Chris R
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
David
5/4/2021
Works great.