Replacement A-Frame Jack For Atwood Mobile Product Jack On Trailer With 2" Diameter Mounting Hole
Updated 04/25/2022 | Published 04/23/2022
Products Featured in This Question
Question:
Team, I am replacing the center mounted Atwood Mobile Product Jack MPD 80274 I purchase a Lippert Model 423192 2k from Amazon and the bottom tongue hole on trailer is smaller than top and upon ion of the new jack the bottom portions diameter was to large. Considering this and the attached photos - do you have a direct replacement that will not only slide down into top hole but bottom portion passes through the smaller bottom one.
asked by: Ken C
Expert Reply:
The Dutton-Lainson A-Frame Trailer Jack # DL22530 is currently our only manual A-Frame tongue jack with a 2" outer tube. The Lippert Quick Drop Tongue Jack # LC733926 that supersedes your 423192 jack along with our other jacks have all gone to the 2-1/4" outer tube diameter.
The Dutton-Lainson Jack # DL22530 has a maximum capacity of 1,000lbs with 15" of travel for a maximum extended height of 29-3/4" from the mounting surface to the ground.
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
A-Frame Trailer Jack - Sidewind - 1,000 lbs. by Dutton-Lainson
- Trailer Jack
- Utility Trailer
- A-Frame Jacks
- Sidewind Jack
- 0 - 1000 lbs
- Manual Jack
- 15 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Dutton-Lainson
more information >
Continue Researching
- Search Results: trailer jack
- Video: Review of CURT Trailer Brake Controller - Universal 7 Way and 4 Way Connector - C76NQ
- Search Results: trailer hitch ball mount
- Search Results: demco a~frame trailer coupler
- Search Results: 7 pin trailer wiring kit
- Search Results: demco trailer hitch
- Search Results: d ring
- Search Results: tongue box
- Shop: Lippert Quick Drop Tongue Jack - Topwind w/ Drive Nut - 14" Lift - 2K
- Shop: Caliber D-Ring Anchor Kit - 5,000 lbs - Zinc - 2 D-Rings
- Shop: Curt Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge
- Shop: etrailer Forged Steel D-Ring Tie-Down Anchor w/ Weld-On Clip - 1" - 15,600 lb WLL - Curved Ring
- Shop: etrailer Forged Steel D-Ring Tie-Down Anchor with Weld-On Clip - 1/2" - 4,000 lb WLL
- Video: Tie Down Side-Mount Spare Tire Mount Set Up
- Video: Feature Breakdown: Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole
- Video: Review of TowSmart Trailer Wiring - 7 Way Molded Trailer Wire Connector With Tester - TS27QR
- Shop: TowSmart 7-Way Molded Trailer Wire Connector - 72" Long
- Shop: Dexter Trailer Axle Beam with E-Z Lube Spindles - 91" Long - 4,400 lbs
- Q&A: Will Standard Battery Operated Drill Operate Lippert Quick Drop Tongue Jack
- Video: etrailer Manual Sidewind A-Frame Trailer Jack Comprehensive Review
- Q&A: What Grade Bolts to Install Demco A-Frame Cast Head Coupler
- Q&A: Can You Replace Stock Coupler On A 2023 ATC Raven Car Hauler With Demco Coupler # DM13205-95
- Video: Review of etrailer Trailer Jack - Enclosed Trailer - Utility Trailer - e88GV
- Video: Let’s Check Out the Buyers Products Recessed Chain Tie-Down for Trailers
- Shop: Trailer Wiring
- Q&A: Replacing Atwood Mobile Products model MPD 80274 Recommendation
- Q&A: Electric Jack Recommendation for Bumper Pull Horse Trailer
- Q&A: Are There Any American Made Trailer Tongue Jacks Available?
- Q&A: Will a 5,000 lb Trailer Jack be Easier to Crank than a 2,000 lb Jack
- Shop: Roof Rack