Trailer Jack Foot Plate Needed for a Jack with 1-5/8 inch O.D. Tubing

Question

Question:

I have a trailer jack, I think it came from Fulton, and the post is 1 5/ 8 O.D. tubing. I am looking for a small foot plate for the 1 5/8 round tubing. Do you have one?

asked by: Randy W

0

Expert Reply:

It sounds like the Removable Steel Foot with Pin for DL22530 A-Frame Trailer Jack by Dutton-Lainson, item # DL22541, will be the closest fit we have for your trailer jack. This foot plate has an inner diameter of 1-3/4 inches which is slightly larger than your 1-5/8 inch outer diameter jack tube.

All of the other foot plates that we carry have an inside diameter of 2 inches.

expert reply by: Robert G

0

Answer 1

You will be able to upgrade your #PD4045KA to use lithium batteries, and in order to do this you'll need to replace the converter (there isn't just an added part aside from the converter that will allow you to do this). So what you need for…

view full answer...

Answer 2

For an A-frame jack that meets that diameter criteria, I recommend the A-Frame Trailer Jack by Dutton-Lainson #DL22530 . This jack will have an inner tube diameter of 1- 3/4 inches and an outer diameter of 2 inches. It is constructed of heavy duty…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Trailer Jack Foot Plate Needed for a Jack with 1-5/8 inch O.D. Tubing

Products Featured in This Question

Continue Researching