See what our Experts say about this Redline Accessories and Parts

• Can Brake Actuator Be Used For Single AND Tandem Axle Brakes On Trailer?
  Good afternoon Courtney. Yes, the same brake actuator can be used on single or dual axle trailers. Just make sure to match up to the style of brakes you have since some actuators are only for drum brakes and some are only for disc brakes. Most trailers only have brakes on one axle so that is completely normal. Some DO have two braking axles though. My 7k dual axle just has one braking axle though. What trailer and brake style do you have? Surge brakes or something else? If you tell...
  view full answer...
• Does The Replacement Mounting Bracket for Kodiak Disc Brake Caliper # KCMB10HRD Come With Hardware
  Hey Justin, The Replacement Mounting Bracket for Kodiak Disc Brake Caliper # KCMB10HRD is just the bracket with no hardware. You would need four each of the following hardware components in order to mount this bracket to the brake flange: Bolt # 7-75 Nut # 6-17 Lock Washer # 5-8
  view full answer...
• Correct Mounting Bracket Bolts for Kodiak Disc Brake Kit
  You are correct, the bolts for the mounting bracket are not included with the Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and KodaGuard - 3,500 lbs # K2R35DKG. What you need is the Brake Mounting Bolt for 7" and 10" Brake Assemblies # 7-75. Along with the bolts you will also want the Mounting Nut for 7" and 10" Brake Assemblies - 7/16" Diameter - Zinc Plated # 6-17 and the Lock Washer for Brake Mounting Bolt for 7" and 10" Brake Assemblies - 7/16" Diameter # 5-8.
  view full answer...
• What Size Nuts and Studs are Used to Mount 7 and 10 Inch Trailer Brake Assemblies
  The studs on the Dexter 7 inc brake assembly, part # 23-47, are 1-1/4 inch long with 7/16 - 20 threads. Brake Assembly mounting bolt, part # 7-75, is 1-1/4 inch long with 7/16 - 20 threads. The nuts, part # 6-17, are also 7/16 - 20. This size is pretty standardized as far as 7 inch and 10 inch brake assemblies.
  view full answer...
• Replacement Hardware for 7" Brake Assemblies and Replacement Stud for Hub
  Hey Brandon! For your brakes you can use the Mounting Bolts and Hardware for 10" Brake Assemblies # BRKH10A. This is also compatible with 7" brake assemblies. If you just want the bolts, you can use the # 7-75. For the hub stud I would need to know the measurements to see if we have one that matches. Are you getting your trailer prepped to take it out this spring?
  view full answer...
• Kodiak Caliper Mounting Brackets Replacement Hardware Size
  The appropriate bolts for use on the Kodiak Replacement Mounting Bracket # KCMB10HRD are bolt # 7-75 which are 20 threads per inch. These are grade 5 bolts that are 7/16" x 1-1/4" long. The corresponding nuts are # 6-17 and the lock washers to use are # 5-8.
  view full answer...
• Grade of Bolt for 10" Brake Mounting Hardware Kit
  The Mounting Bolt # 7-75 that comes with the Kit # BRKH10A for 10" brake assemblies is a grade 5 bolt.
  view full answer...
• Replacement Mounting Bracket and Bolts for Kodiak 3.5K Trailer Disc Brake Kit
  The mounting bracket for the 3.5K Kodiak disc brake kits is # KCMB10HRD. For the bolts to mount the bracket to the brake mounting flange use 4 of # 7-75 per bracket. the matching nut is # 6-17 and the lock washer is # 5-8.
  view full answer...
• Converting Existing Hydraulic Brake System to Electric on Pop-Up Camper
  The Dexter Hub/ Drum you mentioned, part # 8-173-16UC3 would be a proper replacement for you as long as the inner and outer bearings in your existing hubs are # L44649, the grease seal is # 10-9 and the 4-on-4 bolt pattern matches up with your existing hubs. Your existing bearings and grease seals should have reference numbers stamped on them, make sure the numbers on the existing parts match those of the replacements. You will also need electric brake assemblies, part # 23-47 for the...
  view full answer...
• Are Brake Flange Mounting Bolts Included with the Kodiak Disc Brake Kit # K2HR35D
  We do have some hardware that you can use, but the 4 bolts included with the Kodiak Disc Brake Kit # K2HR35D are used for mounting the calipers to the brake mounting flange. To install the brake mounting flange you can use the Brake Mounting Bolt # 7-75 and the Brake Mounting Hardware Kit # BIK-00
  view full answer...
• Replacement Parts Needed for the Titan Hydraulic Brake Kit # T1878800-700
  We do carry the following parts for the Titan Hydraulic Brake Kit # T1878800-700 that you referenced: Uni-Servo Wheel Cylinder RH - # T0977600 Uni-Servo Wheel Cylinder LH - # T0977700 Adjuster Spring - # 046-083-01 Shoe Return Spring - # BP07-105 As well as the mounting bolt # 7-75, lock washer # 5-8, and nut # 6-17 for the assemblies. If there are any other pieces that need to be replaced then it would be easier just to replace the brake assemblies as a whole. a lot of times this is...
  view full answer...
• Parts Needed to Install Electric Brakes On 1995 Coleman Destiny Royale Trailer
  To make sure that you get the correct parts, I would need to know the inner and outer bearing numbers stamped into the metal of the bearings. There are different 5 lug bolt patterns. Use the FAQ I have linked to measure for bolt pattern so you can get the correct hub and drum assemblies. If you do not have EZ Lube axles, you will not need EZ lube hub and drum assemblies. If you do have L44649 inner and outer bearings and the seal has a 1.987 outer diameter and 1.5 inch inner diameter,...
  view full answer...
• Comparison of Dexter and etrailer 7 Inch Brake Assemblies for Trailers with 2,000 Pound Axles
  The Dexter # 23-47-48 and etrailer # AKEBRK-2 brake assemblies are just that. The same part made by two different companies. They're both 7 inch brake assemblies for 2,000 pound axles. Both the left and right hand brakes are included and labeled to make it easier to install. The etrailer brand does include the mounting bolts where the Dexter does not. For mounting bolts use # 7-75. Neither of them include the Mounting Hardware # BRKH7.
  view full answer...
• Kodiak Disc Brake Kit Recommendation for a Dexter D52-8 Axle
  Your current brake mounting flange hardware would work to install the mounting flanges of the Kodiak Disc Brake Kit # K2HR712E. The bolt length should be just fine from your mounting flanges. We have installed these kits on several trailer here and have never had to get longer bolts for the flanges. This kit will also fit the spindle you have on your Dexter D52-8 axle. The ID number for your axle means that it is a Dexter 5,200 lb axle with a 8 lug bolt pattern.
  view full answer...
• Comparing Different Hydraulic Trailer Brakes for Boat Trailer
  Essentially yes, all of them will work for your trailer assuming you have 3,500 pound axles and a 4 bolt mounting flange. However, there are some differences between the brake assemblies you mentioned. The # AKFBBRK-35 are free-backing brakes, meaning they will not engage when reversing with your trailer. If your trailer has a reverse lockout on it then this feature is not necessary. They're coated with an e-coat used for corrosion resistance. The Demco brakes # 40716-15 are galvanized...
  view full answer...
• Titan Brake Assembly Free Back or Universal Difference and Installation, Hardware and Flanges
  The difference between the Titan Galphorite Uni-Servo Hydraulic Trailer Brake Assembly part # T4445300, and the Titan Galphorite Free-Backing Hydraulic Trailer Brake Assembly part # T4423500, is that that part # T4423500 is a Free-Backing brake assembly. It will not apply brake pressure when the trailer is in reverse. So which brake assembly to choose is your choice on whether you want to have brakes on the trailer while in reverse, the part # T4445400, will allow you to have brakes in...
  view full answer...
• Brake Assembly for Use with Dexter Galvanized Trailer Hub and Drum # 8-247-50UC3
  Since your boat and trailer will be used in salt water a galvanized hub/drum is a good idea to give you some corrosion protection. With this hub you can use Demco Galvanized Free Backing Hydraulic Drum Brake Assembly # 40716 (left) and # 40715 (right). These are suitable for a 3500-lb axle and a 4-on-4-inch brake flange mounting pattern. I have linked an installation video for your reference. Even when using galvanized components, it is a good idea to rinse the trailer with fresh water...
  view full answer...
• Recommended Replacement Hydraulic Drum Brakes for Tandem Axle Trailer
  Selecting correct hydraulic drum brake assemblies for your tandem axle trailer requires matching brakes to the axle capacity, the size of your hub/drums (please see linked photo) and to the type of brake flange on your spindles. The linked page will show you all hydraulic drum brakes we offer which are suited to axle capacities from 2500 to 15,000-lbs. Usually a 2500-lb axle will have 7 x 1-3/4-inch brakes but if your trailer has 10-inch hubs it could be that the axles are rated higher...
  view full answer...
  
• Mounting Hardware Recommendations for a Brake Assembly # 18787
  You will need to provide the mounting hardware to install the Brake Assembly # 18787. For bolts you will want Brake Mounting Bolt # 7-75 For locking washers you will want a Lockwasher for Brake Mounting Bolt # 5-8 For nuts you will want a Nut for Brake Mounting Bolt # 6-17 I also attached a video of a brake assembly being installed for you to check out also.
  view full answer...
• What is Brake mounting Bolt # 7-75 Made Of
  The brake mounting bolt # 7-75 is just made of steel. If you can find a galvanized or stainless bolt with the same threads (bolt size is 7/16-20 and length is 1-1/4 inches) you could use it. Check a local hardware store. Bring one of the old bolts with you so you are sure to get a good match. If you go with these steel bolts the matching nut is # 6-17 and the lockwasher is # 5-8.
  view full answer...
• Correct Mounting Bolts and Hardware for Galvanized 10 Inch Marine Trailer Brake Assembly 40716
  The 10 inch brake assembly, # 40716, does not come with mounting bolts. You would need bolts like # 7-75 to mount the assembly to the brake mounting flange. For matching washers, use # 5-8 and for nuts # 6-17.
  view full answer...
• Recommended Hub And Drum for Electric Brakes With 4 On 4 Bolt Pattern For 1973 Scamp Trailer
  The hub we offer that will work with electric brakes and has a 4 on 4 bolt pattern, is part # 8-173-16UC3. You are correct that this hub and drum will only work with 7 inch x 1-1/4 inch brakes. The bearings, races, and seals are included with this assembly. I have attached a product review video for this hub/drum you can check out. The electric brakes that will work with this drum is designed for axles rated up to 2,000 lbs. The brakes have a 4 bolt mounting flange. For the right hand(passenger...
  view full answer...
• Does the Demco Hydraulic Drum Brake Assembly Come With the Drum?
  I do have a solution for you but the answer to your question is no, the Demco Hydraulic Drum 3,500 lbs - 10" Brake Assembly # DMSB24429M is just the brake assembly without the drum. Keep in mind that when selecting a brake assembly and hubs that you make sure they will have the same weight capacity that your axle has. You will want to make sure that whichever brake assembly you choose that you get the Right Hand side as well, in this case it would be the Hydraulic Drum Brake part # DMSB24428M. I...
  view full answer...
• Availability of Electric Drum Brake Assemblies Like # 23-468 Without Integrated Mounting Bolts
  All of the electric drum brake assemblies we offer in the 10 x 2-1/4-inch size that are suitable for 3500-lb axles have mounting bolts installed. We do offer separate brake mounting bolts in a 7/16-inch size with 20 threads-per-inch, part # 7-75. We also offer washers # 5-8 and nuts # 6-17.
  view full answer...

Do you have a question about this Accessories and Part?