Arrives before Christmas 
6-5/8" x 2-3/16" Oval. Waterproof light serves as either a side marker light or a clearance light. Chrome bezel provides finished look. Surface mount - hardware not included. 2-Wire design with 0.180 male bullets. P2 rated. Red LEDs.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The circuit board is sealed, which means that water will not damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we're taking look at the Optronics LED clearance or side marker light. This light functions as a clearance or side marker light for your trailer. It features a sealed, waterproof design. It's a two wire design, so you have one for power, and one for ground. It comes with the .180 male bullet connectors on there. If you don't want them on there, you can cut them off, strip back the wiring for hard wire applications.This is an LED system.
LED's make great replacements for incandescent lights. They last longer and they burn brighter, they're more efficient. With LED's you don't have to worry about replacing bulbs and you don't have to worry about brittle filaments. It's P2 rated, it's SAE and Department of Transportation compliant. It features a really nice, clear polycarbonate lens with red LED's and it has this chrome bezel that ads a clean finished look and covers the installation hardware.Mounting hardware is not included.
It does have a two mount hole design. The mount holes are separated on center by about 4 and 5/8 inches. Now I did take an overall length measurement, going edge-to-edge. I'm going to turn it around, a little bit better to measure the backside here. A little bit more accurate.
I took a measurement, edge-to-edge, and got a measurement of about 6 and 5/8 to 6 11/16 of an inch, right in that area. Going this direction, I got a measurement of 2 and 1/4 inches. The overall thickness, just the housing area, is about 11/16 of an inch.We're going to go ahead and hook it up to power that way you can see what it looks like with some power running through it. Then we'll also turn off our overhead lights so you can see it in a lower light setting. This unit sends out a nice, consistent signal.
It's a very bright light, it's a 4 LED or 4 diode design. The multi-diode design really helps optimize the overall light output. When it comes to the warranty on the unit, Optronics puts a lifetime warranty on the LED's. That's going to do it for today's look at the Optronics LED clearance or side marker light.
Average Customer Rating: 5.0 out of 5 stars (4 Customer Reviews)
6-5/8" x 2-3/16" Oval. Waterproof light serves as either a side marker light or a clearance light. Chrome bezel provides finished look. Surface mount - hardware not included. 2-Wire design with 0.180 male bullets. P2 rated. Red LEDs.nice packaging
ship quick and fast good price tha nks
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.