2-1/2" Round. Low-profile LED trailer light serves as either a side marker or clearance light. Built-in reflex reflector. Snap-on polycarbonate lens. Surface mount with included gasket - hardware not included. 2-Wire design. P2 rated.
Features:
Specs:
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the Optronics round LED clearance with side marker trailer light with the red lens and the reflex reflector. Now this round trailer light can function as either a clearance or side marker light, and it does have the built in reflex reflector on it to eliminate the need for a separate reflector on your trailer. This does use LEDs. They make great replacements for incandescent lights. They'll last 50 times longer, and they're more efficient because they'll provide brighter light with less power output, and there's no bulbs to replace or brittle filaments to break. Does use this nice durable polycarbonate snap on lens on a black ABS housing.
It does have a red lens over one white LED. This is compatible with the 12 volt DC systems.It is a surface mount design to the trailer. Now the hardware to install this is not included. It does have the attached gasket here that helps create a weather tight seal when you install it. You'll notice it's a two wire pigtail, which will hardwire into the trailer.
The red is for your power, white is for your ground. And this is a P2 rated light, which produces a 90 degree beam pattern.A few dimensions on this, the diameter on this light is right at two and a half inches. Thickness on it, just the light itself is a half an inch. If you add the gaskets, about three quarters of an inch. Power draw on this at 12 volts is 0.073 amps.
This does have a lifetime warranty on the LEDs. What I'm going to do now is hook this up to some 12 volt power to show you how bright it is. We'll go ahead and take our power wire, hook that up to the red, take our ground, hook that up to the white. Then with those attached, turn on our 12 volt power.There you go. You can see the light come on.
Go ahead and turn off the overhead light, and there you can see the LED. Keeps touching it. Okay, you can see it shining. I'll go ahead and turn back on our overhead lights. Turn off our power. But that should do it for the review on the Optronics round LED clearance or side marker trailer light with the red lens and the reflex reflector.
Average Customer Rating: 4.8 out of 5 stars (46 Customer Reviews)
2-1/2" Round. Low-profile LED trailer light serves as either a side marker or clearance light. Built-in reflex reflector. Snap-on polycarbonate lens. Surface mount with included gasket - hardware not included. 2-Wire design. P2 rated.The lights were exactly as I would hope they would be. I am very pleased. The service was outstanding. It was delivered within a couple days.
They replaced damaged marker lights on a vintage camper restoration. Close enough to original. Of course brighter and more efficient.
Overall good quality, matches my OEM and price was great.
Correct part the first time, quick shipping, kept me informed as needed, no complaints here. I will definitely use etrailer.com for future purchases.
It was one of the easiest orders i have ever placed!
Nice Job - etrailer!
I was able to find what I needed and I placed order. I was notified my order was in process and when sent. Received order when in a couple of days. Thanks
The part came in quickly and no damage.
Just what I was looking for.
Exactly what I needed and so far they work great.
It’s what I need it
hard to find surface mount side marker light for old RV, just what i was looking for.
Fit perfectly
Came exactly as advertised and was easy to install. Nice marker that’s highly visible.
Great! Quality products, timely deliver y.
exact fit.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.