Brake Mounting Hardware Kit for 7" and 10" Brake Assemblies

Ask the Experts about this Redline Accessories and Parts

• Will the 10" Hydraulic Trailer Brakes Fit a 2004 EZ Loader Tandem Axle Boat Trailer
  In order to determine if the Hydraulic Trailer Brake part # AKUBRK-35R for right hand side or part # AKUBRK-35L for left hand side will fit your 2004 EZ Loader Boat Trailer you will first want to confirm that you have hydraulic brakes which is more than likely the case. Then, you will want to know your axle capacity which can be found on the centerline of the axle. These assemblies are rated for use on axles up to 3,500 lbs. Once the axle capacity is confirmed you will then want to measure...
  view full answer...
• Torque Specs for etrailer Electric Trailer Brake Kit AKEBRK-35-SA
  The brake mounting hardware for the # AKEBRK-35-SA, which can be obtained with part # BIK-00, should be torqued between 45-70lbs during installation; if you don't have a torque wrench you'll want to tighten the bolts until the lock washer is flat against the backing plate. In order to do the initial, manual adjustment on the # AKEBRK-35-SA you will use the star style adjustment wheel at the bottom of the assembly; this process is briefly shown around the 2:00 mark in the installation...
  view full answer...
• Torque Figure for Installing 10 inch Trailer Brake Assemblies
  The nuts to secure brake assembly # AKUBRK-35 should be torqued to between 45-70 foot lbs. If you don't have a torque wrench close at hand we have # ALL944001. We offer 4 nuts and lock washers as part # BIK-00.
  view full answer...
• Torque Spec for 10 Inch Dexter Electric Brake Assembly
  According to Dexter, the nut should be torqued to between 45-70 foot lbs. If you don't have a torque wrench close at hand, Tighten the bolts until the lock washer flattens, which will put you really close to the correct torque. We offer 4 nuts and lock washers as part # BIK-00.
  view full answer...
• 10 Inch Hydraulic Trailer Brake Assemblies for etrailer 3.5K Hub and Drum # AKHD-545-35-K
  The trailer hub and drum assembly # AKHD-545-35-K will take Bearing Buddy 1.98, # BB1980A or # BB1980A-SS (for stainless steel). For complete brake assemblies that fit this hub and drum I recommend the free-backing etrailer brakes # AKFBBRK-35L for the left side and # AKFBBRK-35R for the right side. If this is going on a boat trailer I recommend # AKFBBRK-35L-D for the left and # AKFBBRK-35R-D for the right. These brakes have a corrosion resistant dacromet coating ideal for marine applications. If...
  view full answer...
• Hub and Drum Assemblies and Brakes for Timbren 2,200 Pound Axle-Less Suspension System
  Timbren axle-less suspension system # ASR1THDS02 can be used with hub and drum assembly # 84546UC3-EZ. For the right hand brake assembly use # 23-27 and for the left use # 23-26. For nuts and washers I recommend # BIK-00. And for adjuster plugs, # BP10-220.
  view full answer...
• Recommended Brake Assemblies For Dexter Axle 3500 lb And 5200 lb
  I reached out the the manufacturer and found that they have two possible axles that meet that criteria. One is definitely more likely your application than the other, but I will give you both brake assembly options. For a 3500 lb axle, you will want the Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500 lbs # AKEBRK-35-SA. This will give you both the left and right assemblies. There is a sticker to help you with which assembly fits which side....
  view full answer...
• Electric Trailer Brake Assemblies to Fit 10x2-1/4 Inch Dexter Drum
  Yes, the Electric Trailer Brake Assembly # AKEBRK-35L is the left hand brake to fit your Dexter drum. For the right hand side you'll need # AKEBRK-35R. If you would prefer self-adjusting brakes you would use # AKEBRK-35R-SA for the right and # AKEBRK-35L-SA for the left. Self-adjusting brakes are much easier to maintain and do not require to be adjusted manually as the brake pads wear. To connect the brake wires on the trailer to the magnet wires on the new brakes you can use the...
  view full answer...
• Electric Brake Assemblies And Grease Seal Recommendation For Scamp Trailer
  The Dexter 7 Inch Electric Trailer Brake Assembly, part # 23-47 is what you need for the left hand on your Scamp trailer. For the right hand you would need part # 23-48. These are designed with a 4-bolt mounting flange. These are used on the axle you said you have on your trailer, and will work well even though they say they have a 2,000 lb rating. The hardware kit you need for mounting each side is part # BIK-00. You will need a kit for each side. Adjusters plugs are available as well....
  view full answer...
• Recommended Trailer Braking System For 30 Foot Pontoon Trailer With Tandem Axle
  With a 6000 lb capacity on your pontoon trailer and 13 inch wheels, you most likely have 3500 lb axles. For this, you will want Electric Trailer Brake Assembly - Self-Adjusting - 10" - Right Hand - 3,500 lbs # AKEBRK-35R-SA and the left side assembly # AKEBRK-35L-SA. The mounting hardware kit is # BIK-00. You will want to run 10 gauge wire to these brake assemblies and it can be purchased by the foot # 10-2-1. To finish your wiring, I recommend the Epicord 7-Way Molded Trailer Plug...
  view full answer...
• New Wheels and Brakes for 2002 Coleman Westlake Pop-Up Camper
  The # AM3S331 ST185/80D-13 wheel/tire combo you specified should work well for you. The brake assemblies you need will depend on the diameter of your brake drum, which is most likely a 7x1-1/4 inch (7 inches inside diameter, 1-1/4 inside depth). If that's the case, you'd use the AxleTek # AKEBRK-2L for the drivers side and # AKEBRK-2R for the passenger side. There isn't a self-adjusting 7 inch diameter brake assembly available. If you have a 10x2-1/4 inch brake drum, you'd use #...
  view full answer...
• What Are Mounting Bolt Hole Sizes For Replacement Hydraulic Trailer Brakes
  The hydraulic trailer brake you referenced, Item # AKUBRK-35L, fits 4-bolt flanges with a 2-7/8-inch hole spacing and is suitable for use on a 3500-lb axle. It fits the driver's side and brake mounting bolts are included. For the passenger side, use Item # AKUBRK-35R. Nuts and lock washers are sold separately and are available in brake mounting hardware kit Item # BIK-00 (one kit needed per wheel). I recommend the Brake Adjustment Spoon Item # W80630 as well. Links with additional...
  view full answer...
• Replacement Brake Assemblies For 1977 Miley Horse Trailer
  A 10 inch brake assembly is typical for a 3500 lb axle has 2-1/4 inch shoes. As long as there is room in the hub for this, I recommend using the wider shoe. It will give you more surface contact to function correctly. My recommendation is to use Electric Trailer Brake Assembly - Self-Adjusting - 10" - Right Hand - 3,500 lbs # AKEBRK-35R-SA along with # AKEBRK-35L-SA for the left hand side. If you need mounting hardware for these assemblies you can use # BIK-00. These self-adjusting...
  view full answer...
• Are 10 Inch Hydraulic Trailer Brake Assemblies Compatible with DICO Model 60 Actuator
  The Hydraulic Trailer Brake, Uni-Servo, Free Backing, 10 inch, Right-Hand # AKFBBRK-35R, that you referenced, will work well with your Dico Model 60 actuator. This brake assembly measures 10 inches x 2-1/4 inches and has a 4 bolt mounting flange bolt pattern. For the Left-Hand Assembly, you will want to use part # AKFBBRK-35L. All of our 10 inch x 2-1/4 inch hydraulic drum brake assemblies are for 3,500 pound axles. If you need new brake mounting hardware, you can use the hardware...
  view full answer...
• Are Brake Flange Mounting Bolts Included with the Kodiak Disc Brake Kit # K2HR35D
  We do have some hardware that you can use, but the 4 bolts included with the Kodiak Disc Brake Kit # K2HR35D are used for mounting the calipers to the brake mounting flange. To install the brake mounting flange you can use the Brake Mounting Bolt # 7-75 and the Brake Mounting Hardware Kit # BIK-00
  view full answer...
• Parts Needed to Add Electric Drum Brakes to Pop-Up Travel Trailer
  If your Safari already has a brake controller and functional 7-way socket, and your trailer already has brake flanges and 7-way wiring, then to add electric drum brakes you will need the left- and right-hand brake assemblies, hardware to mount them (# BIK-00), compatible hub/drum assemblies, a breakaway kit and wiring to connect the brakes to your trailer. The linked article on adding electric drum brakes to a trailer may interest you. It covers everything needed. Brakes should be...
  view full answer...
• Mounting Hardware Needed to Install etrailer.com Self Adjusting 10 Inch Brake Assembly
  For installation hardware compatible with 10 inch brake assemblies, like the etrailer.com Self Adjusting Brake Assembly # AKEBRK-35L-SA that you referenced, you will want the Brake Mounting Hardware Kit for 7 and 10 Inch Brake Assemblies # BIK-00. This kit includes 4 nuts and 4 lock washers that fit on pre-installed mounting bolts on the back of the brake assembly. This installation hardware kit comes with the parts needed to install one brake assembly. So you will want one kit for...
  view full answer...
• Recommended Parts To Add Electric Trailer Brakes To Pop Up Camper With 2000lbs Axle
  Thank you for all the details on your axle and bearings! Your list of parts is dead on. The Dexter Electric Trailer Brake Kit w/ Parking Brakes # K23-103-104-00 is a great option if you are looking to add a parking brake. If you aren't planning on adding a parking brake you can use the Electric Trailer Brake Kit # AKEBRK-2. The Dexter # K23-103-104-00 comes with the required hardware, but the Electric Trailer Brake Kit # AKEBRK-2 will require the Mounting Hardware # BRKH7 or two of...
  view full answer...
• Do Trailer Brake Assemblies Include Hubs and Drums
  Parts # AKEBRK-35L and # AKEBRK-35R are left and right hand 10 inch brake assemblies for 3,500 pound trailer axles. Use # AKEBRK-35 to purchase both of them together. The hub and drum assemblies and the bearing kits are not included. A 3,500 pound axle that uses 10 inch brakes and has a 5 on 4-1/2 bolt pattern likely uses bearings # L44649 and # L68149. You'll want to verify these are the correct numbers on your trailer. If they are then the hubs you need are # AKHD-545-35-EZ-K for...
  view full answer...
• Recommended Electric Trailer Brake Assemblies For 3500 lb Axles
  All of our brake assemblies for 3500 lb axles are 10 inch by 2-1/4 inch. This is industry standard size, so I would be surprised if you have a different measurement, but you can grap a tape measure and check. The next size up is 12 inch and the next size down is 7 inch. For you application, I recommend the Electric Trailer Brake Assembly - Self-Adjusting - 10" - Right Hand # AKEBRK-35R-SA and the left hand assembly # AKEBRK-35L-SA. If you want new mounting hardware, you can use...
  view full answer...
• Adding An Axle To An 83 Dilly Single Axle Boat Trailer With Timbren Axle-Less System
  Yes. You can add a second axle with a Timbren Axle-Less Trailer Suspension System - Spindle w/Brake Flange - Off-Road Tires - 2,200 lbs # ASR1THDS02. When adding a second axle, you will want to ensure that they are the same capacity and use the same size wheels, etc. When adding a second axle the pivot point of the trailer changes, so where your current axle sits is where you would split the distance for a tandem axle application or where your center hanger would need to be if you were...
  view full answer...
• What Is Included With Electric Trailer Brake Assembly For 3,500-Lb Axles
  The etrailer Electric Trailer Brake Assembly, part # AKEBRK-35L is designed for the driver side of the trailer and the brake assembly for the passenger side is part # AKEBRK-35R. These brake assemblies comes with the mounting bolts. The washers and nuts for these brake assemblies are sold separately and are part # BIK-00. Since these are manual adjust brakes, you may need the Brake Adjustment Spoon, part # W80630. A brake controller is needed with electric brakes and if you do...
  view full answer...
• Parts Needed to Add Electric Trailer Brakes to a 1998 Jayco Pop Up Trailer
  The brake assemblies # 23-47 and # 23-48 are for 2,000 pound axles. If you have a 2,000 pound axle this will work great for you. You can reuse your current cotter pin and spindle nut. For the hardware for the brake assemblies you can use # BIK-00. Brake flanges are universal as long as they have the same number of holes. Yours is are 4-bolt which is what these brakes use. Higher rated axles will use a 5-bolt pattern. If your axle is rated higher than 2,000 pounds let me know and...
  view full answer...
• Torque Rating to Secure 10 Inch Brake Assemblies to a Trailer Axle
  The nuts to secure brake assembly # AKEBRK-35R-SA should be torqued to between 45-70 foot lbs. If you don't have a torque wrench close at hand we have # ALL944001. We offer 4 nuts and lock washers as part # BIK-00.
  view full answer...
• Parts Needed to Add Electric Drum Brakes to 3500-lb Front Axle of Tandem Trailer
  We offer electric drum trailer brakes for 3500-lb axles in the 10 x 2-1/4-inch size that you can see on the linked page. All work with 13-, 14- or 15-inch wheels and you can choose from either manual-adjust or self-adjust types by clicking on the filters on the page. Be sure to always select matching left- and right-hand brake assemblies for your axle, such as # AKEBRK-35L-SA and # AKEBRK-35R-SA. All of these 10-inch brakes use a 4-bolt brake flange mounting pattern. (Your hub bolt pattern...
  view full answer...
• Mounting Hardware for etrailer.com Electric Brake Assembly # AKEBRK-35L
  The # AKEBRK-35L brake assemblies will use a 7/16 inch mounting nut. You can use the Brake Mounting Hardware Kit # BIK-00. This kit includes 4 nuts and 4 lock washers to install 1 brake assembly. The mounting pattern for the # AKEBRK-35L brake assembly is standard.
  view full answer...
• Electric 10 Inch Trailer Brakes and Mounting Hardware for 3500 Pound Trailer Axles
  Based on your spindle measurements you have a 3,500 pound trailer axle. These axles use the 4-bolt mounting flange for electric brake assemblies. The 10 inch brake assemblies # AKEBRK-35L for the left side and # AKEBRK-35R for the right are the correct brake assemblies! The mounting studs are already on the brakes so you would just need the hardware kit, # BIK-00. One is needed per brake assembly. I also recommend brake adjustment tool # W80630 which will make adjusting the brakes easier.
  view full answer...
• Selecting Replacement Electric Trailer Brakes and Mounting Harwdware
  Electric trailer brakes like the etrailer # AKEBRK-35R that you referenced should be selected based on your axle capacity and brake flange mounting pattern. The brake you referenced fits 4-bolt flanges with a 2-7/8-inch hole spacing and is suitable for use on a 3500-lb axle. These brakes fit hub/drums with a 10-inch diameter x 2-1/4-inch width, such as # AKHD-545-35-K. For washers and bolts to mount these brakes use kit # BIK-00; you'll need one kit per wheel. For tang washers for...
  view full answer...