See what our Experts say about this CURT Heavy Duty Receiver Hitch

• Where is Drop Dimension Measured on Curt Hitch # C87CR
  Hey Brett, the drop of the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C87CR that you referenced would be measured to the top of the hitch opening. The drop of this hitch is 18 inches. How much drop do you need?
  view full answer...
• Trailer Hitch For A 2015 Kenworth T270
  Hi Garrett! We do have options for your 2015 Kenworth T270, but there are not going to be any custom fit hitches available. If I were doing this, I would go with the Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 44" Wide # C87CR. It can tow up to 20K, has a 2-1/2" receiver, and is American made. You will need to do some welding to get it attached, but I think it's the best option. Especially with your frame looking to be 34" wide (at least that I could find). What...
  view full answer...
• Gooseneck and 5th Wheel Hitch for 2023 Silverado 5500 Flatbed
  Hey Craig! For a 5th wheel and gooseneck setup I recommend the B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks # BWGNRK1500. This will give you a gooseneck hitch and then it can be paired with the B&W Companion Flatbed Gooseneck-to-5th-Wheel Trailer Hitch Adapter # BWRVK3050 for 5th wheel towing. For a hitch I recommend the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C99CR. This fits frames up to 44" wide and comes with 18" brackets you can cut down to best...
  view full answer...
• Availability of Hitch that Could Fit 2008 International IC RE Bus
  Hey Derek, only solution would be a universal Class V hitch like the # C87CR as we don't have anything custom fit for your bus. This has drop brackets that can be set at any width up to 44 inches so it should hopefully be something that would work for you but you would need to check out the rear of your bus. The drop these brackets have is 18 inches.
  view full answer...
• Recommended Class V Hitch for a Ford F-53 Chassis
  Hey Robert. To add a class V hitch to a 2002 Ford F-53 chassis, I recommend the Curt Class 5 Universal Weld-on Hitch w/ Brackets item # C99CR. There is not a custom fit receiver for the F-53 models because the chassis can be modified by the RV manufacturer and would require different options for different RVs. The Curt item # C99CR includes universal brackets that will need to be welded to the outside of your frame. It fits frames up to 44" wide so this will fit great. It has a 16,000...
  view full answer...
• Recommended Weight Distribution System for a Travel Trailer w/ a 500 lbs Tongue Weight
  Hey Jack, congrats on the new trailer! For a close to 500 lbs tongue weight, I recommend the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item # EQ90-00-0600. This system works with tongue weights ranging from 200 lbs - 600 lbs so you'll be good if you weren't fully loaded or wanted to pack your trailer up differently. The sway control brackets mount from 27" - 32" back from the center of the coupler so you'll want to make sure you have space on yours at these locations....
  view full answer...
• Will Curt Class V Hitch Fit 2024 Freightliner S2RV
  Hey Tom! The Curt # C15803 is designed to fit certain Ram trucks. Some people might have modified the hitch or just welded it on to get it to fit their Freightliner S2RV but it won't be able to just bolt on. If you're going to go that route you're better off using the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C99CR (2" receiver) or # C87CR (2-1/2" receiver). This fits frames up to 44" wide and the brackets can be cut down or modified as needed for proper fitment. What will...
  view full answer...
• What Heavy-Duty Trailer Hitch For Trailer With 2,000 lbs of Tongue Weight
  Hi Jason, We have a couple of options for a trailer hitch with a 2,000 lb tongue weight capacity that you can have welded on. While there isn't anything specific for your '98 Minnie Winnie, you just need to measure your frame from outside to outside, as well as the amount of drop from the frame you need. Here are the options: Frame Up To 44 Inches Wide - 9 Inch Drop From Frame: Curt Class 5 Universal Weld-on Hitch # C37CR - 18 Inch Drop From Frame: Curt Class 5 Universal Weld-on Hitch...
  view full answer...
• Availability of 18k Hitch With 2-1/2" Receiver for 2023 Chevy Silverado 5500
  Hey Kirtis! Since there are no custom fit hitches for the 5500 the best options is the Curt Class 5 Universal Weld-on Hitch # C87CR. This has a 2-1/2" receiver with a max gross trailer weight rating of 20,000 lbs. It fits frames up to 44" wide (yours is approximately 34") and has 18" drop brackets which can be cut to size for your application. What will you be using the hitch for?
  view full answer...
• Is There 2-1/2 Inch Weld-On Hitch For Bus
  Hi Zachary, There are a couple options for a 2-1/2" weld-on hitch for a school bus. Both are for frames from a minimum of 18" to a maximum of 44" and the right one depends on the amount of drop you need. The drop will be from the frame of the vehicle so you can use either depending on that: - 9" Drop: Curt Class 5 Universal Weld-on Hitch # C37CR - 18" Drop: Curt Class 5 Universal Weld-on Hitch # C87CR
  view full answer...
• Recommended Class V Trailer Hitch for a 2016 Georgetown RV
  Hey Jeremy, for your 2016 Georgetown RV you can use the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C87CR. This is a universal class V hitch that will fit frames measuring 18" to 44", has a 20K capacity, and has a 2 1/2" receiver opening. If you have a wider frame than 44" then you could use the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C59CR which will fit up to a 62" wide frame.
  view full answer...
• Trailer Hitch for 2001 Ford E-450 With 10k Capacity
  Hi Brad; the Curt Class 5 Universal Weld-on Hitch # C87CR you ordered is the solution here. There are no custom hitches so the only option is a universal weld-on. This does have a 2-1/2" receiver opening so if you want a 2" instead the # 41990-16 you looked at will also work.
  view full answer...
• Trailer Hitch for 2007 GMC W4500 5.2 Diesel
  Hey Jeremy! You won't find a custom fit hitch for your 2007 GMC W4500, but a weld on will definitely work. I recommend the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C99CR. This fits frames up to 44" wide, has a 2" receiver, and can handle up to 16,000 lbs. The brackets can be cut down to whatever length works best for your truck. A 2-1/2" receiver version is available as well # C87CR. What will you be hauling?
  view full answer...
• Trailer Receiver Hitch for Flatbed Cab and Chassis Pickups
  The side plates in the Curt Class 5 Universal Weld-on Hitch # C87CR have only been tested by Curt in the vertical position. With that they are not sure how the mounting brackets will hold up if mounted horizontally. I recommend the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver # 3371809055 for you to consider. It Is rated for 17,000lbs with a 2" receiver and is specifically designed to deal with the overhang caused by flatbeds. The hitch is designed to fit trucks...
  view full answer...
  
• Recommended 2-1/2" Trailer Hitch for a 2006 Thomas School Bus
  I do have an option for you but there aren't any custom fit trailer hitch options for a 2006 Thomas School Bus. That said, we do still have universal options which can be installed either via welding or cutting/drilling. For this, I recommend the Curt Class 5 Universal Weld-on Hitch part # C87CR which uses very large side plates so you have a lot of room for error when modifying them to make fit. It has a class v rating with 2-1/2" opening which is great for heavy duty towing.
  view full answer...
  
• 20,000LB Trailer Hitch Receiver Options For a 2022 Tiffin Allegro Bus Motorhome With Tag Axle
  I do have some weld-on options for you as I unfortunately do not have any custom fit bolt on options and I cannot look at the detailed specs for your 2022 Tiffin Allegro Bus 45 OPP Motorhome. We have 2 sets of the Curt Class 5 receivers with either a 44" or 62" wide receiver tube which are all rated for up to 20,000lbs trailer weight and 2,000lbs tongue weight. You will need to select the correct width based on your frame and the amount of drop you will need to clear any rear fascia panels....
  view full answer...
• Availability Of Heavy Duty Trailer Hitch Receiver For 2000 International 4900 Truck
  There are a few options for your 2000 International 4900 Truck, but there is not a custom fit receiver available. The Super Titan 4000 Weld-On Trailer Hitch with 3" Receiver Opening, 25,000 lbs. # 38124 could work but requires the frame on your truck to be 34 to 34-1/2" wide. This option has a 4000lb tongue weight rating and a 25000lb trailer weight rating, but uses the less common 3" receiver. Another option is the Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver -...
  view full answer...
• Will Curt Trailer hitch Receiver C15860 Fit 2016 GMC Sierra 2500 With Service Body
  I reached out to my contact at Curt and it is possible that the Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" # C15860 will fit your 2016 GM Sierra 2500 with a Service Body as long as it did not start life as a cab and chassis truck. The main thing to look for is that when the service body was installed that they did not modify the frame of the truck as the # C15860 uses factory mounting points. If your truck is a cab and chassis model, or if the frame was...
  view full answer...
• Can the Curt Class 5 Universal Weld-on Hitch Be Drilled and Bolted
  The Curt Class 5 Universal Weld-on Hitch part # C87CR is designed to be welded to the frame of a vehicle. I cannot recommend bolting and drilling unfortunately. The frame will need to be clean and clear of obstructions before welding. In regards to the actual welding, this would need to be done by a trainer professional, make sure precautions are taken such as unhooking the battery. That said, I'm no welding expert so you would need to refer one for these types of questions.
  view full answer...
• Does the 2.5 Curt Class V Universal Weld-on Hitch Come with Longer Brackets
  The Curt Class V Universal Weld-on Hitch part # C37CR is offered with longer brackets, part # C87CR. The brackets are a bit taller than you were looking for but could be cut down easily.
  view full answer...
• Solution for Class V Hitch on 2011 Fleetwood Expedition Motorhome
  For hitch fabrication we only offer the receiver tube like the # E-11 or # C49511. You would need to take this to a local fabricator and they would be able to fashion a hitch and brackets that will fit your 2011 Fleetwood Expedition Motorhome. The other option would be to use one of the universal Class V hitches we have listed for your motorhome. We have the Curt # C47CR with a 9" drop and the Curt # C99CR with an 18" drop. Both options have a 2" receiver. The # C37CR and # C87CR are...
  view full answer...
• Heavy Duty Hitch for 2018 Coachmen Pursuit Precision Motorhome 27DS
  I do have a solution, but the # C15800 will not fit your 2018 Coachmen Pursuit Precision Motorhome 27DS. For a heavy duty hitch you need the Curt Class 5 Universal Hitch # C87CR. This fits frames up to 44" and has the same high capacity with a 2-1/2" receiver. If you want a 2" receiver you can use the # 15902 instead. You will need to take the hitch to a certified welder for installation.
  view full answer...
• Availability Of Heavy Duty Trailer Hitch Receiver For 2008 Country Coach Allure Motorhome
  While we do not have a custom fit trailer hitch receiver that is confirmed to fit your 2008 Country Coach Allure Motorhome you may be able to install a universal Class V hitch like the Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2-1/2" Receiver - 44" Wide # C87CR which works with vehicle frames between 18" - 44" wide. The # C87CR has a 2-1/2" receiver, a 2000lb tongue weight rating, and 20000lb trailer weight rating, but will need to be welded to the frame of your vehicle by a...
  view full answer...
• What Hitch Will Fit A 2008 Peterbilt 220 With a 31" Frame
  That’s a great question, Leandro! We do have a couple solid options that will work well for your 2008 Peterbilt 220, especially with the width you’re working with. The first option is the Curt Adjustable Hitch # C37CR. This one has frame brackets that can be adjusted up to 44" wide, so you’ll be able to position them to match your 31" frame spacing. The brackets do need to be welded to the cross tube, but once installed, it gives you about a 9" drop from the frame. If you’re looking...
  view full answer...

Do you have a question about this Heavy Duty Receiver Hitch?