See what our Experts say about this CURT Accessories and Parts

• Where is Brake Controller Adapter Plug Located In 2002 Dodge Ram Pickup
  The green connector in your truck is not the correct plug. It is normally a blue plug like what I have shown in the photo that plugs into the adapter part # C51332 if you are using a Curt brake controller like part # C51170. There will be a port to plug into if the truck came with a factory 7-way plug just to the right of the emergency brake. If the 7-way plug was installed after-market, you will need to see how far the wires from the plug are extended so you can complete the install...
  view full answer...
  
• Recommended Brake Controller w/a Compatible Harness to Replace a Draw-Tite I-Command
  I sure can Cynthia! To replace your Draw-Tite brake controller, I recommend the Curt TriFlex NEXT item # C24VV and the Curt Wiring Adapter for Cequent Trailer Brake Controller Wiring Harnesses item # C51520. This brake controller has been built to withstand the extreme heat of being kept inside a hot vehicle. The Curt TriFlex NEXT Trailer item # C24VV is a proportional brake controller that slows or stops your trailer with the same amount of force you're using to slow or stop your Ram...
  view full answer...
• Troubleshooting Flashing 0.0 Error Message on Curt Discovery Brake Controller # C84VV
  The troubleshooting guide included in the instructions for the Curt Discovery Brake Controller # C84VV that you referenced does not include this particular display issue, a flashing 0.0, among the possible display messages. My technical contact at Curt has never seen this particular message displayed on a Discovery brake controller. He suggested that either the display is malfunctioning or the controller is bad. Since your brakes are not engaging when you press the pedal with the trailer...
  view full answer...
• Where Is the Brake Controller Plug on a 2008 Dodge Ram 1500
  The correct brake controller adapter plug you are looking for is blue however, it will only have four pins as you mentioned which means the one you have located in not correct. The correct plug you will be looking for and can find in the attached photo is located to the left of the intermediate shaft on the steering column. This plug can also be seen in the attached video. The correct adapter for you if you have a Curt brake controller like the Curt TriFlex Trailer Brake Controller part...
  view full answer...
  
• Choosing Between Curt TriFlex and Tekonsha Prodigy P3 Brake Controllers
  Hi Dan; this is a pretty easy choice, I would definitely pick the P3 over the Curt TriFlex # C43GV. The P3 wins for reliability alone, and it has more features. The only real advantage with the TriFlex is the lower cost. However, right now the P3 isn't available, and Tekonsha is for sale. We don't know what the future holds for the brand, and I you probably won't be able to get warranty support if you need it. For an equally reliable brake controller I recommend the Redarc Tow-Pro Liberty...
  view full answer...
• Do Brake Controllers have Constant Power or Do they Wire Into a Ignition/Accessory Power Source
  Brake controllers such as # C74VV will have constant power once installed. They need to have constant power otherwise they would reset every time you turned off the vehicle. Brake controllers have what is basically a sleep mode. After a certain amount of time the "go to sleep" and draw only a few milliamps of power so they will not drain the vehicle battery. If your 2007 Dodge Ram did not come with a factory 7-Way trailer connector then you will also need wiring harness # C51515 for the...
  view full answer...
• Best Brake Controller for a 2006 Dodge Ram 2500
  The Curt Assure Trailer Brake Controller with Dynamic Screen item # C49UR, you were looking at, would be a great brake controller for your 2006 Dodge Ram 2500. It is a proportional brake controller designed for use with electric or electric-over-hydraulic trailer brakes. If your Dodge Ram came with a 7-way connector or a 4-way connector then you will want the Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In item # C51332. This adapter plugs into a port behind your...
  view full answer...
• Best Brake Controller For 2005 Dodge Ram 3500 With Bumper Pull Camper
  First off, the proportional brake controllers are definitely recommended for a situation like this. They provide better response so they are safer, and also have less wear and tear on your trailer's brakes since they apply braking pressure equal to your vehicle's braking. For your 2005 Ram 3500, I recommend the Curt TriFlex # C24VV with adapter # C51332. Curt is a very trustworthy and reliable brand, and this controller is one of the most reliable controllers on the market. It is good for...
  view full answer...
• Installation of Brake Controller on 1997 Ram 1500 Club Cab with Factory Trailer Plug
  We do appreciate your continued patronage and I think we can assist you with this. If you can't find the plug and the dealer doesn't offer any help on this, then you can hard wire in the controller to your 1997 Ram 1500, so you will be able to install the controller it'll just be a bit more time consuming. You will need a circuit tester like the # PTW2993 to test wiring functions under the dash, and you may need some butt connectors like the # DW05745-5 to complete your wiring connections....
  view full answer...
• Curt Venturer Trailer Brake Controller Installation in 2006 Dodge Ram 2500
  Any trailer brake controller, including the Curt Venturer # C74VV, uses a 4-wire hookup. All brands and models of trailer brake controller have a white ground wire, a black 12V power wire, a red input signal wire and a blue output wire. The white ground wire connects to battery negative; the black power wire connect to the battery + terminal through a 30-amp circuit breaker or fuse; the red input signal wire connects to the cold side of the brake light switch above the brake pedal; and...
  view full answer...
  
• Are Brake Controller Wiring Harnesses for the 2004 Dodge Ram 2500 Universal
  Hello Ed. Brake controller wiring harness # 3020-P for the 2004 Dodge Ram will work with Tekonsha, Draw-Tite, and Reese brake controllers that have a plug and not just loose wires. Curt harness # C51332 will work only with Curt brake controllers. And as far as I could ascertain Hayes harness # HA81782-HBC only works with Hayes controllers. All of these harnesses are also only for controllers that have the plug on them and not just loose wires. Another option, for controllers that do...
  view full answer...
• How to Find the Stop Light Wire on a 1997 Dodge Ram 1500
  I do have an option for you but unfortunately, we would not have access to the wiring diagram for a 1997 Dodge Ram 1500. In order to find the cold side of the brake pedal which is the wire that will need to be spliced into to install a brake controller, you would need to test each wire with a circuit tester like part # PTW2993 for the wire that only receives power while the pedal is depressed. Once you find this wire you can use a quick splice connector like part # SWC501746-1 to avoid...
  view full answer...
• What Is The Blue Connector For In The Glove Box Of The Ram 2500
  I will be happy to explain how why the blue plug would not be installed in the wiring bundle. The blue plug is an adapter that's used to install an after-market brake controller. When installing a brake controller vehicles sometimes already have a plug and play connection under the dash. A plug and play connection is a connection that does not require the brake controller to be hardwired to the vehicle. Some brake controllers like # 90195 will need a plug or adapter like you have the #...
  view full answer...
• Parts Needed To Install Brake Controller on 2005 Dodge Ram 1500
  Since your 2005 Dodge Ram has the factory installed 7-Way, to install a brake controller you will just need the brake controller itself and the proper wiring harness to plug it into your Ram. If you go with the Curt Venturer, # C74VV, the only other part you will need is wiring harness # C51332. I have included a link to the installation details for you. The wiring harness plugs into a connector already on your vehicle. The connector is located underneath the dash, to the left of the...
  view full answer...
• Curt Brake Controller Pigtail for a 2003 Dodge Ram and Curt Discovery Brake Controller
  The Curt brake controller wiring harness for the 2003 Dodge Ram is # C51332. If you will be moving the controller back and forth from one truck to the other I also recommend a second mounting bracket, # C51124.
  view full answer...
• Quality Trailer Brake Control for a 2006 Dodge Durango
  You are thinking of Tekonsha brake controllers. They are pretty much the leader in the brake controller industry. The Curt controllers would not be my first choice. I prefer Tekonsha controllers because they have a long proven track record of quality and performance. The Curt controllers are a less expensive option but they are new to the brake controller industry. They did have some performance issues initially but they are improving. I recommend the Tekonsha P2, # 90885. This is a proportional...
  view full answer...
• Is Anything Else Needed to Install Curt Venturer Brake Controller on a 2005 Dodge Dakota
  If your 2005 Dodge Dakota has the factory 7-Way then you need the Custom Wiring Adapter # C51332 to install the Curt Venturer # C74VV. Sure you can hardwire it but this gives you a great way to easily connect and disconnect the controller without having to install it permanently. Same thing if you don't have the factory 7-Way. You will need the Universal Adapter # C51515 to avoid splicing the controller directly into your vehicle wiring. This adapter does require splicing but the end with...
  view full answer...
• Brake Controller for 2008 Dodge Durango with Factory Wiring Harness for Tow Package
  You need to purchase both the Curt Brake Controller # C51170 and the Curt Wiring Harness # C51332 for your Dodge Durango as they are sold separately. This allows you to plug directly into the port that comes with the tow package and is located directly under your dash.
  view full answer...
• Recommended EOH Trailer Brake Controller for a 2001 Dodge Ram
  The Curt TriFlex Trailer Brake Controller part # C24VV is an excellent option for a 2001 Dodge Ram and will work with trailers that have electric over hydraulic brakes. It also offers plug-in-play installation when used with the Curt Custom Wiring Adapter part # C51332. This will be a great option that will serve you well
  view full answer...
• Curt Brake Controller Recommendation for 2005 Dodge Ram 2500
  The price for the Venturer controller part # C74VV and install harness part # C51332 is tough to beat but a proportional brake controller will be a much better option. Proportional controllers sense how hard you are applying the brakes and apply the trailer brakes the same way. Time-delayed like the Venturer put out a preset amount of braking power so they aren't as effective. So instead the Triflex part # C24VV with the install harness # C51332 would be the better option for your 2005...
  view full answer...
• Wiring Adapter for Curt Brake Controller Installation in 2006 Dodge Ram 1500 Quad Cab 4 X 4
  If your 2006 Dodge Ram 1500 has a factory 7-way socket on the bumper then the correct brake controller adapter harness for your Curt controller is part # C51332. If this is how your truck is equipped then the connection port will be located under the steering wheel, just to the right of the emergency brake pedal. If your truck does not have the factory 7-way and the under-dash port for a brake controller then you can do a hard-wire type installation using part # ETBC7. This install kit...
  view full answer...
• Install Harness for Curt Assure Brake Controller in 2007 Dodge Ram 2500
  To install the Curt Assure brake controller part # C49UR in your 2007 Dodge Ram 2500 all you need is the correct install harness # C51332 and you'd be set. This plugs into the brake controller port you have under your dash.
  view full answer...
• Curt Spectrum Brake Controller Showing no Trailer on 2000 Dodge Ram 2500 After Replacing Connectors
  Yes, you are definitely on the right track. If your Curt Spectrum Trailer Brake Controller # C51170 is still not showing a trailer is connected and you have already replaced the connectors, I think it has to be a short either on the brake wiring or the brake magnets themselves. Before replacing your brake assemblies entirely, start by just checking the wires to the brake magnets (if you have not done so yet) and look for wires that may be pinched or otherwise damaged and fix as necessary....
  view full answer...
• Components Needed for the Curt Venturer Brake Controller to be Used on a 2004 Dodge Ram Pickup
  If you prefer using the Curt Venturer Trailer Brake Controller, part # C74VV, then we have the adapters required to make them work. If you already have a 4-way on your 2004 Dodge Ram Pickup, then the adapter for the Venturer is part # C51332. This will plug into the Venturer and the factory brake controller port of your pickup. I've linked to a video review of this adapter for you to look at. To convert your 4-way into a 7-way, you will need the etrailer Universal Installation Brake Controller...
  view full answer...

Do you have a question about this Accessories and Part?