Where Is the Brake Controller Plug on a 2008 Dodge Ram 1500

Question

Question:

Purchased a curt brake contrller for my 2008 dodge ram 1500. It has a tow package from factory. There is a blue plug under dash. But it is not a 4 pin. Im sending pics of what i have and what i need thanks in advance for any help.

asked by: Daniel B

0

Expert Reply:

The correct brake controller adapter plug you are looking for is blue however, it will only have four pins as you mentioned which means the one you have located in not correct. The correct plug you will be looking for and can find in the attached photo is located to the left of the intermediate shaft on the steering column. This plug can also be seen in the attached video. The correct adapter for you if you have a Curt brake controller like the Curt TriFlex Trailer Brake Controller part # C24VV is the Curt Custom Wiring Adapter for Trailer Brake Controllers part # C51332.

expert reply by: Conner L

0

click to enlarge

Answer 1

If your 7-way says 'Mopar' on it, it should be the factory 7-way although it might have been a dealer installed instead of a factory installed option. Only vehicles with the factory installed tow package will have the blue under-dash…

view full answer...

Answer 2

I cannot be sure as to what the plug you have found is for but I can assure you it is not for a brake controller. The brake controller plug (if equipped) for a 2008 Dodge Ram is rectangular with four pins like the photo I have attached for you, there…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Where Is the Brake Controller Plug on a 2008 Dodge Ram 1500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching