Replacement Clearance and Side Marker Lights for a 2019 EZ Loader Tandem-Axle Boat Trailer
Updated 06/16/2026 | Published 06/12/2026
Products Featured in This Question
Question:
Im rewiring a 2019 EZ Loader tandem-axle boat trailer saltwater use, lights get submerged at launch and replacing the fender marker lights. Current setup: Wesbar grommet-mount marker lights in molded plastic/composite fenders. The rubber grommet is embossed Wesbarinch appears to be the 15-series grommet, 221588 and the lens is stamped SAE P2 DOT. The fender opening measures 3inch x 1-1/2. The original incandescent lights had direct wire leads with inline bullet connectors, which is what corroded. My requirement: Im eliminating every plug/quick-connect on the trailer, so Im looking for a SUBMERSIBLE LED marker light with bare hardwired wire leads two-wire, since the fenders are plastic and cant self-ground — not the 2-pin plug style and not .180 bullets. I know the Wesbar LED 47-203667/47-203668 fit this grommet, but they use the plug-in pigtail A46PB, which Im trying to avoid. Questions: 1. Is there ANY LED clearance/side marker light with direct hardwired leads that fits the Wesbar 15-series grommet 221588 / a 3inch x 1-1/2inch opening? 2. If not in that exact footprint, what hardwired two-wire submersible LED marker would you recommend for a plastic fender, and how would you mount it over or in this opening? 3. If the answer is really the plug style is the only option in this footprint,inch is there a sealed/molded-harness version of the A46PB pigtail youd recommend for saltwater? I need 2 amber and 2 red. Thanks!
asked by: Cory
(click to enlarge)
Expert Reply:
Hey Cory, welcome back and thanks for the picture. That's a tough situation you're in. I went through all of our submersible lights and I do not have a suitable replacement that does not require the use of the item # A46PB pigtail.
My only solution is to use the Thinline LED Clearance and Side Marker Light - Submersible item # AL91RB in red and item # AL91AB in amber. They measure 2-1/2" L × 1-3/16" W × 7/8" D. These lights work with the following mounting brackets and grommets:
Mounting Bracket item # A91BOB
Grommet item # A91GB
Mounting Grommet w/ Built-in Wedge item # A91GZB
The Right Angle 2-Wire Pigtail item # A46PB is the only option I have. They come in longer pigtails but nothing like what you're looking for.
If you have any additional questions, go ahead and click on the box that says Add Comment and I'll be happy to answer them.
(click to enlarge)
Product Page this Question was Asked From
Thinline LED Clearance and Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber
- Trailer Lights
- Clearance Lights
- Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 2-1/2L x 1-3/16W Inch
- Amber
- Optronics
more information >
Continue Researching
- Q&A: Replacement Angled Mounting Grommet for Optronics AL91PB Side Marker Light on Skeeter Trailer
- Shop: Mounting Grommet w/ Built-in Wedge for A91 or AL91 Series Lights - Black
- Video: An In-Depth Look at the Mounting Grommet w/ Built-in Wedge for A91 or AL91 Series Lights
- Q&A: Replacement Wedge Rubber Grommet for Optronics A91 Series Clearance Lights
- Article: Trailer Lighting Requirements
- Article: Trailer Wiring Diagrams
- Q&A: Upgrading Lights on 2000 Tracker PT175 Trailer to LED
- Q&A: Dimensions of PET95FJ With Grommet
- Q&A: Availability of Red Peterson LED Clearance and Side Marker Light
- Q&A: Replacing Horse Trailer Lights
- Q&A: Replacement Clearance Lights For a 2017 Skeeter Boat Trailer
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: How to Bleed Your Trailer Surge Brakes
- Article: Most Popular Wheel Bearings
- Article: Wiring Trailer Lights with a 5-Way Plug (It's Easier Than You Think)
Todd A.
6/16/2026
I soldered my leads and used heat shrink connectors. You could use liquid tape over that. You could use epoxy or liquid tape on the back of the light and plug.