What Size Hole is Needed to Mount Optronics 2-1/2 Inch Side Marker Light with Reflector and Grommet

Question

Question:

What hole size do I need to cut to fit a 2-1/2inch led clearance light and grommet in?

asked by: Arlo

0

Expert Reply:

The Optronics Sealed 2-1/2 Inch Round Trailer Clearance, Side Marker Light # MC57AB along with the Round Grommet - Floush Mount # A55GB will require you to cut a 3 inch diameter mounting hole. You will also need the Right Angle 2-Wire Pigtail Plug # A46PB to pair with the female connection on the Optronics light.

I have attached video reviews of these products for you to look at.

expert reply by: Chris R

0

Gmw

8/8/2025

3" is too large for a 2.5" grommet. 2.75" is the correct home size for the grommet!

Answer 1

You will need to cut a 2-5/16 inch mounting hole for installation of the 2 inch Round Flush Mount Grommet, item #A54GB, and the Sealed, 2 inch Round Trailer Clearance and Side Marker Light, item #MC53RB. The proper wiring pigtail for this light is…

view full answer...

Answer 2

The #STL22CCRB lamp you referred to is typically mounted in a grommet, like part #A70GB, which in turn is mounted in a bracket like part #337LB1SS. If you were planning on cutting a hole to mount the lamp and grommet, the hole will need to measure…

view full answer...

Answer 3

Hello Xavier, thanks for reaching out. We do offer a 7-way wiring harness for the 2017 Honda Pilot. For that you can use the following: - T-One Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector #118286 The video linked below…

view full answer...

Answer 4

The 07100 bearing number you referenced is an Timken bearing that has the same dimensions as #L44643.

view full answer...

Answer 5

When I reached out to the Dometic they informed me that the foot pedal itself is not replaceable. Which means you can either try to rig something up to get it to work, or you will have to replace the entire toilet assembly. If you're ok with…

view full answer...

Answer 6

Hey James, we have compartment latches like you are looking for with the Bauer Products RV Baggage Door Slam Latch part #BA57FR which is designed to fit a cutout of 3-1/4" tall x 4" wide. It's hard to say exactly what you cut out is but…

view full answer...

Answer 7

Hey Joe, The Dexter Swing-Away Coupler #DX53CR is made out of a steel construction, not cast iron. So none of the item itself is a cast iron material. Are you specifically looking for one that is?

view full answer...

Answer 8

It does sound like the previous owner did not install the assemblies correctly. An easy way to make sure you have the brakes on correctly is to lock at the actuating arm. It should always point towards the front of the trailer. I have included a…

view full answer...

Answer 9

The correct nut for the Dexter Shackle Bolt for Double Eye Springs part #007-126-01 is the Replacement Flange Nut for Dexter Trailer Suspension Kits part #006-092-01.

view full answer...

Answer 10

The item you selected, Sealed 2-1/2 Trailer Light, part #MC57AB, is a 2-1/2 inch light that will mount into a 3 inch hole using 2-1/2 inch grommet, part #A55GB. The hole size to mount a 2 inch round light flush mounted would be 2-5/16 inches. The…

view full answer...

What Size Hole is Needed to Mount Optronics 2-1/2 Inch Side Marker Light with Reflector and Grommet

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching