View Cart

Ford Expedition Brake Controller

Select Vehicle Year

  
Brake Controller

Available Years for Ford Expedition Brake Controller


Brake Controller

Brake controllers are an essential part of a towing system with electric trailer brakes, and they offer a much-needed emergency braking feature. We offer high quality controllers from manufacturers such as Draw-Tite, Tekonsha, Valley, Hidden Hitch and Hopkins. Featuring both time-delay and proportional models, we have the right controller for any application. Brake controller wiring adapters are available for many vehicles, allowing for simple plug-and-play installation. Hardwire kits are also available to make any installation hassle-free.

Find your custom fit brake controller wiring adapter for a plug-in application by selecting the year of your vehicle to the left. We offer custom fit plug in adapters for many of the most popular vehicles, including Ford, Chevrolet, Dodge, GMC, Nissan, and Toyota.





Brake Controller Manufacturers


Search For Custom Fit Ford Expedition Accessories
Select A Category Below



Ford Expedition Brake Controller Videos

Tekonsha P3 Brake Controller Installation - 2012 Ford Expedition

Jake: Hey guys, it's Jake here with etrailer. Today we have a 2012 Ford Expedition we're going to be taking a look at, and I'm going to show you how to install the Tekonsha P3 Brake Controller. This is going to give you the ability to use electric brakes with your vehicle. This brake controller is going to activate your trailer's brakes in proportion to your vehicle's braking action.You notice when I push on the brakes here, the voltage is going to go back, which is going to send back a signal to your trailer brakes. With our arrows over here on the side, you're going to have a 14 level adjustability; 0 all the way up to 14. When first setting it to your trailer, you're going to want to start in the middle at 7 and go down or up, depending on what size trailer you might have.They do have three different settings of boost that you can push from this button over here on the right.



Trailer Brake Controller Installation - 2006 Ford Expedition

Today in our 2006 Ford Expedition, we'll be installing the Contra 00:02:35 Prodigy P2 Break Controller, part number 90885 with a direct fit wiring harness or pigtail 00:00:11, part number 3035-P. First we'll go ahead and locate the manufacturer's break controller tow hood. Here, next to the diagnostic link for the vehicle's computer, we'll find the gray, five pin plug which will be the manufacturer's tow port. Next, we'll take the break controller bracket and find a suitable mounting location. Then using the hardware provided with the install kit we'll go ahead and secure the bracket in place. Next, we'll take the wiring harness, plug into the gray connector on one side and route the other up through our break control bracket or pocket. Once we have our harness in position, we can then go ahead and take the wiring harness and plug it into the back of the break controller. Once we have it plugged into the break controller, we can then go ahead and put our break controller into the pocket and lock it down.



Trailer Brake Controller Installation - 2000 Ford Expedition

Today on our 2000 Ford Expedition, we're going to install part number 90195, the Prodigy P3 Brake Controller. We'll be also using an Adapter Cord, part number 3035-P from Tekoncha. We'll start off with that part. We'll look for the port that's underneath the dash. It's right next to the diagnostic port. You'll go ahead and point it out and then go ahead and plug the cable into it. All right.



Trailer Brake Controller Installation - 2008 Ford Expedition

Today on our 2008 Ford Expedition we will be installing the Tekonsha Prodigy P3 trailer brake controller. Part number 90195. The first step to installing our brake controller is to remove this panel. To do so there are 3 push fasteners that hold this in place and 3 screws down here at the bottom. With those screws removed and set to the side, gently pull back on the panel, and remove it from the vehicle. For the installation it's not necessary to remove the panel. I went ahead and did just to make sure I didn't damage any other interior parts, because it can be kind of tricky to get a screw driver or your drill in there to install the bracket.