Can The ETBC7L Be Installed On A 2024 Toyota Grand Highlander Hybrid

Question

Question:

I have a 2024 grand Highlander hybrid that has a four pin adapter on it well the seven pin conversion kit for grand Highlander work with it? Seen some online reviews that says that the hybrid is different from the grand Highlander that is gas powered only.

asked by: Fred R

0

Expert Reply:

Hi Fred!

The 7-Way RV Upgrade Kit for Trailer Brake Controller Installation - 12 Gauge Wires # ETBC7L will have no issues working with your 2024 Toyota Grand Highlander hybrid. It will piggyback off your existing 4-flat and you will just need to run a wire to the 12 volt battery (not the hybrid battery) and you are good to go. I can't say I have heard anyone we have recommended this to have a problem with their hybrid.

Do you have a brake controller picked out already? Or is this more to just get a 7-way?

expert reply by: Lazer S

0

ETBC7L Wire Functions
(click to enlarge)

Fred

9/2/2025

We would need a brake controller as well. Any recommendations?

Lazer S.

9/3/2025

@Fred I have a couple for you. The first is the Curt Echo Wireless Brake Controller - 7-Way Plug-in w/ Bluetooth App - Up to 2 Axles - Proportional # C51180. This works perfectly with the # ETBC7L and will require no other wiring as it connects to your smartphone. It is very popular for this reason. However, I am not a huge fan of it as I prefer to use my phone as a phone and don't like having to download apps to run things like this. You can add the manual override button # C83HR so you don't have to have your phone out an open at all times, but if I were installing a brake controller, I would go with this next option. Check out the Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional # RED52VR. This will require the # ETBC7 as it has the wiring that goes up to the cab of your vehicle, but getting this installed isn't overly difficult. Once the controller is also installed, all you will see is the knob. You will need to drill a very small hole for the post that the knob fits on to go through, but I think it's still worth it (you probably have an open accessory switch port somewhere on the dash). It's also very easy to set up and use, and it's one of the most reliable ones on the market. If I didn't have a factory controller in my Silverado already, this is what I would install. What kind of trailer will you be towing?

Answer 1

Hey Ray, so we have the part #18159 which would work great to secure the 7-way of the #ETBC7L that you'll be installing with the Curt Echo #C51180. It's also pretty easy to install too.

view full answer...

Answer 2

Hello Alex, thanks for reaching out. We actually custom make our own wiring kit which is designed specifically for this purpose. You can use the Universal Installation Kit #ETBC7. This kit will contain all of the components needed to upgrade your…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Can The ETBC7L Be Installed On A 2024 Toyota Grand Highlander Hybrid

Product Page this Question was Asked From

Continue Researching