Parts Needed To Make A Complete Thule T2 Pro XTR Bike Rack

Question

Question:

My girlfriend ordered this part by mistake not from you all and is unable to return it. Any chance you would have the additional part s I need to make it whole? Thanks for all the help

asked by: Jamie

0

Expert Reply:

Hi Jamie,

In order to get a fully complete Thule T2 Pro XTR bike rack # TH83JV you would need the following parts:

Replacement Spar Tube Assembly for Thule T2 Pro XT - Black # 7524703001
Replacement Spar Tube Assembly for Thule T2 Pro XT - Black # 7524703002
Replacement Front Wheel Holder for Thule T2 Pro Platform Bike Racks # 8528023001
Replacement Rear Wheel Holder Assembly # 7521682001

The hardware for installing these parts would also be needed but you'd need to reach out to Thule directly for that.

expert reply by: Kevin C

0

Jerred H.

1/5/2026

Hey Jamie, were you able to track down the hardware from Thule to finish off your T2 Pro XTR bike rack? Knowing how it all came together could help others trying to complete their racks too.

Answer 1

Other than the two bolts in the shaft the only thing left to be done when trying to remove the 2 Bike Add-On for Thule T2 Pro XTB #TH9036XT would be to loosen the linkage using the hex key. The linkage is threaded into the center bolt hole below…

view full answer...

Answer 2

For your T2 pro, the Replacement Front Wheel Holder for Thule T2 Pro Platform Bike Racks - Qty 1 #8528023001 and the Replacement Rear Wheel Holder Assembly for Thule T2 Pro Platform Bike Racks - Qty 1 #7521682001 are the trays you are seeking. They…

view full answer...

Answer 3

I reached out to my contact at Thule and she wasn't able to offer any additional advice with regards to removing the 2 Bike Add-On #TH9036XT from your T2 Bike Rack. There are 2 bolts at the connection point on the mast that need to be removed…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Parts Needed To Make A Complete Thule T2 Pro XTR Bike Rack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching