Can The Curt Front Mount Trailer Hitch Receiver # 31108 Be Installed On Models Without Tow Hooks

Question

Question:

I dont have tow hooks on my Chevy Silverado 2500 HD 04. Will the front hitch receiver fit? How do I install it without tow? Hooks?

asked by: David R

0

Expert Reply:

Hey David,

The Curt Front Mount Trailer Hitch Receiver # 31108 comes with hardware and a diagram for models without tow hooks so you'll still be able to install it.

expert reply by: Kevin C

0

31108 Installation diagram
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 5

Hey Kenny, welcome back! The reason for that note is because all of the new systems since 2025 use R32 refrigerant due to EPA regulations. Any 2024 and older systems use R410A and their parts are not compatible with the R32 units. It doesn't mean…

view full answer...

Answer 6

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hey Neil. The 18,000 Btu Furrion Chill Cube RV Air Conditioner item #LC34DX fits a 14-1/4" x 14-1/4" cutout which is pretty standard on RV's. If you meant to write Dometic instead of domestic then yes it'll fit in your existing…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

Hey Matt, Furrion typically has 4 wires running to their thermostats and the Chill Cube Thermostat #LC74DX is no exception. The harness you see with the thermostat would plug into the Chill Cube's controller and has 4 wires to extra wire to to…

view full answer...

Answer 12

Hi JD; the Furrion Chill Cube #FR49TD air distribution box has a vent on it you can open and close. See the picture attached below. When it is closed it forces more of the air through the ducted system. Assuming you have a ducted system you will need…

view full answer...

Can The Curt Front Mount Trailer Hitch Receiver # 31108 Be Installed On Models Without Tow Hooks

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching